hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
I have a custom design with NRF9160. I try to use the debug output of the NRF9160 DK, but on the debug-out of the nrf91 DK it is not recognize (target Voltage is visible at...
we use nRF52833,SDK:S140,17.2,sometims,the device goes into trouble and the error code is 0x715.
here is the call stack:
/port.c:128 0x00027482 PendSV_Handler
/port...
When developing a BLE device with nRF52840, the following error occurred when importing the header file for spi communication.
ERROR ['NRF_DRV_SPI_INSTANCE_0' undeclared...
I am using FreeRTOS with FatFS/SD card. SDK is nRF5_SDK_17.0.2.
If different tasks access FatFS API in different task, is it thread-safe? i.e. Task A access file A and task...
Hi,
I'm integrating the ble_app_uart example into my project. However, the UART interrupt works a little differently than I expect. I initialized the UART with APP_UART_FIFO_INIT...
Hello
I followed the doc blew for building sample
- https://infocenter.nordicsemi.com/topic/ug_gsg_ses/UG/gsg/intro.html
- https://devzone.nordicsemi.com/nordic/nordic...
Hi,
Currently I have a NRF52832 chip that I am using in a project. The chip is inaccessible since it is inside a device -- I have been performing software updates via the...
I've mistakenly closed the case https://devzone.nordicsemi.com/f/nordic-q-a/85450/insufficientresources-error-message-while-performing-usb-dfu?ReplyFilter=Answers&ReplySortBy...
Hello,
I am referring to the ISP4520 example code .
I would like to change the I2C(TWI) pin assignments as below.
SCL:P0_07 / SDA:P0_12
But I can't find where to set...
SDK 17.1.0
nRF52840 DK central + nRF52840 peripheral device
Hello,
I'm attempting to set up reading characteristic values on the nRF52840 DK as a central from a peripheral...
hi,
We are currently having some problems erasing flash，The problem recurrence rate was 1%，the recurrence rate of specify chip problems is 100%，Here are some scenarios as...
Hi,
In secure_bootloader(SDK17.1.0) example, I want to replace the ECDSA_P256_SHA256 with ED25519, what should I do?
I tried to modify sdk_config.h, but the build didn...
I have the EV BT-840 DK and I have the AT firmware installed. With AT commands I am able to connect and send data to other BT-840DK. Right now I flip the AT command switch...
Hi Guys, I am following the numbers and tutorials and setting up Visual Studio on a windows PC and installing the Nordic extensions. I get as far as a successful build but...
I was able to work with the mfrc522 RFID card reader through SPI on nRF9160dk. The application was developed using connect SDK v1.5.1
When we tried developing using SDK...
