Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Hello, i did my own custom board with a nrf52805 and I'm trying to put a module with different frames and when I do that my app is disconnecting 5seconds after. I didn't have...
Hello all,
I`m trying to use k_poll, it`s working okay, I just have an hard fauld error that drives me crazy, I have in main an loop which listen to k_pool_signals, the...
Hi,
Why I use the function m_device_state_set(cons, PM_DEVICE_STATE_SUSPENDED); to close the serial port is still a large current:38.80uA?
The verification method is as...
Hi there
I wrote SDK 17.2 ble_app_hrs to the module.
When connecting to an Android device, Empty PDUs will no longer be sent. I checked the RTC COUNTER, but it is incremented...
SDK: NCS 1.8.0
Based on: Peripheral LBS example
Central: Mobile (iPhone)
Peripheral: nRF52832
Hi,
We are in the process of adding FOTA to our custom project and...
We are using nRF52833 with DFU secure bootloader and implemented DFU master/host on ESP32 BLE. We observe that DFU bootloader get stuck in above locations in softdevice more...
Hi Nordic
I have been using your example on USB MST to embed it into my application
Everything works ok, but in the main loop im constantly polling for USB power event...
I'm looking at the nRF Connect SDK Matter documentation, and the intro page states :
"If you are new to Matter, check also the tutorials on DevZone ."
The link in...
I am using nRF5340DK and would like to send and receive data to computer via UART1 and pins "TX", "RX", "CTS" and "RTS" using USB TO RS232 SERIAL CONVERTER.
This way I...
Hello Nordic, I have a problem. I'm running the nRF9160DK with three sensors and an sd card reader. The three sensors and the sd-card reader are connected via SPI. Due to...
Hi,
I would like to generate interrupts triggered by an input clock pin at 2 MHz to sample an 8-bit digital signal. I am trying this with an nRF5340. Up to this point...
Hello,
I am working with a nRF52833 and I am no longer able to use my JLink Base to flash it. I was previously able to flash it and there was no hardware change at all and...
Hello,
I am writing code in zephyr on nRF52840. I am advertising my BLE. and we have a stable android app (built-in a flutter). My problem is when I am trying to write an...
