Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Using SDK15.3 on 52840. I've got a UART set up talking to something at 9600 baud..
The short course here is that imediately after init, I get an IRQ with a NRF_SERIAL_EVENT_DRV_ERR...
Hello, I´m working on my audio project and I try to stream some audio data (currently a 1 kHz square wave signal with 3.3 V peak) over I2S. The audio signal is sampled by...
Hello, I tried to implement the zephyr executing time functions API on my nrf52 hardware and I got the above error. According to my SoC documentation (nRF52833), this hardware...
Dear Devzone:
I am developing the design of a PCB that implements the nRF9160 SiP module, I have doubts about how to make the communication interface to connect the module...
Hello,
I used the nRF Connect plugin for VCS to create a Zephyr/BLE project. It appears this copies many files into the "build" directory which are required to compile the...
I am getting compilation errors when using the DT_ macros to access SPI bus child entries.
Overlay file:
&spi1 { compatible = "nordic,nrf-spim"; status = "okay"; sck-pin...
hardware : nRF52840DK-52840
SDK : NCSV1.7.1
IDE:Visual Studio Code
I wanted to printf float value , so I set CONFIG_CBPRINTF_FB_SUPPORT=y in my prj.conf file, my application...
Hello,
I'm using following code to read ADC values. The minimum sampling time I'm able to read the ADC reliably is 60ms. I want to lower it to say 5ms or 10ms.
Is there...
To the kind attention of Nordic support team,
reading at this: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.8.0/nrfxlib/softdevice_controller/README.html#softdevice...
Hello,
I have I am trying out the LPN sample from nRF5 SDK for Mesh v5.0.0 and I have an issue where certain mesh configuration messages (e.g. set publication, add application...
Hi, We have custom nrf52840/33 peripherals, advertising every couple hours, and passing/receiving information from centrals running node.js version 12.22.5 with pc-ble-driver...
Hi, I work on custom board, which have NRF52833 and IS25LP016D SPI flash. I tried with SPI flash sample but SPI flash driver IS25LP016D was not found! err message show on...
Hello,
I want to use DTM FW for my design and have to update Tx & Rx pins to 21 and 20 respectively. Looking at the files in $\ncs\v1.8.0\nrf\samples\bluetooth\direct_test_mode...
Hi
I measured the CW output power of several DevBoards (nRF52832 and nRF52840) and the output power is much lower than expected.
Setup:
nRF52832 or nRF52840 DevBoard...
