Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
So from my understanding from the zephyr documentation, if I want to use 7 bit I2C addressing, don't set I2C_ADDR_10_BITS. I am wondering how I can make sure this macro is...
Hi,
How do I add the System ID characteristic (UUID 0x2A23) from the Device Information Service (DIS) using Kconfig commands in the prj.conf file?
For example, I can add...
Hello,
I am having a strange problem with nRF Connect SDK for VS Code, and would appreciate some help.
I don't know what I did, but suddenly I am not able to "Generate...
I am developing a product that uses the chip of NRF52832 and runs FreeRTOS on the chip to manage my task list. However, I found that the program would be stuck in the idle...
I've got a custom board that uses an nRF52832. Firmware was built with NCS v2.6.1.
My hardware uses a MIC826 IC for ensuring the nRF52 is held in reset whenever the power...
I'm looking for a beginner's guide to setting up external flash on the nRF9161 DK. I saw nRF Cloud Multi-service as an example, but its docs did not explain what was needed...
Hello,
I have had posted several times over the years and solved a problem or two. I find it very thorough to finish out a post by concluding my findings. This said, I...
Hello everyone,
My problem is that I could not flash one of my NRF5340 Audio DK boards, the program that is installed before was headset configuration right. I am using...
We wanted to share our feedback as we recently went through Zigbee 3.0.1 BDB/cluster certification using the ZBOSS with our end device product. While we were ultimately able...
I just got a new set of nRF5340 Audio DKs and I may have been too fast on the trigger trying to flash the boards with example programs. I'm using VS Code, and I'm a newbie...
I want to know where did the "desired_data_size" value in le_audio_rx_data_handler come from?
And why "data_size != desired_data_size" means the pkt is bad frame?
Thank...
Hi,
We have recently acquired a new firmware engineer, and would like to get him set up with a development environment for developing code for our product. The problem...
Code running on nRF52833 devkit version 1.0.0 that continuously sends an empty 500 kbit/s radio packet:
Code running on nRF54L15 devkit version 0.8.1 with chip revision...
NCS v2.8.0
nRF52832 DK & nRF52840 DK
peripheral_uart unmodified example
nRF52832 DK with peripheral_uart example has about 1.3 mA current when LED off and sleep mode...
We want to use a BL6554PA (based on the nRF52840) as a thread node and enable the integrated Skyworks SKY66112-11 front-end module with PA and LNA to increase our range. I...
