Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I need to send custom messages to models on my devices and I need to use a vendor model like I've seen other people on this forum use. But when I load the nRF Mesh...
Hello,
We are interfaced the nrf52811 with LSM6DSO32 through i2c and LSM6DSO32 is connected to Auxiliary(Temperature MAX30208) sensor through mode 2 connection. here I am...
I am trying to learn to use the nrfx API to control the nrf5340.
My installation is the NCS 1.6.0 with SES on OSX
It seems like nrfx most of the API devices are supported...
I'm trying to find a battery for my application and I need to know the max (peak) current draw for the nRF9160. On page 63 of the user guide, the max is 435mA with the specs...
I have a function which writes data to the external flash which is using a FAT file-system further using block device implementation of the SDK. Whenever I am calling the...
Hello,
I am working on nrf5340DK board and with a sample example "central_uart" under ncs->nrf->samples->bluetooth & "peripheral_uart" from ncs v1.5.1. I wanted to send...
Hello,
I am trying to setup test environment using nRF9160DK(PCA10090, 1.0.0)
Dev kit is located in Montreal, Canada.
I started with nRF9160_DK_Getting_Started_Guide...
I am trying to update the bootloader using BLE DFU and it does not seem like the app is launching after the bootloader update.
I currently have an app that works with the...
Hello, I am developing a Zigbee OTA client / server application. My code is based on the example from the 4.1.0 nRF5 SDK. From the example I took only the code related to...
Hi,
What is the the status of android and IOS support of bluetooth 5.0 long range ?
It would be great if you can give us a list of device that support long range (of course...
Hi,
i have some issues with nrfutil, i can't properly perform an OTA DFU over thread, either nrfutil cannot find ncp.hex or it stuck in "thread DFU server is running....
Hi,
I made a project around the peripherial-uart sample with a custom board for a nrf5340 chip.
I work with win10, Toolchain nrf Connect SDK 1.6.1
I can build it and...
Hi,
I'm attempting to develop chip to chip communication where an nRF9160 acts as an I2C master communicating with an nRF52840 acting as an I2C slave.
I got reasonably...
Hello.
Now, I'm trying to combine ble_app_beacon and spis.
I succeeded in building and it generates hex file.
The problem is that the device stops sending BLE data ...
