hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi, DevZone, thanks for help : )
I'm try to porting DK Board's Ble Bonding function to Target Board.
TARGET : nRF52840
SD: s140_nRF52_v7.0.1
SDK: nRF5_v16.0.0
...
To whom it concerns:
I'm a little new to Bluetooth SIGs launch studio and need a little guidance on the correct QDID to utilize for my product using Nordic SDKs.
I have...
Hello,
I'm working on a program that receives the temperature over TWI, saves the temperature in a string to flash memory, then adds this string to an NDEF message to be...
Hello,
I have 4Pcs same PCBAs and same firmware, the current values as below:
2.2uA
3.3uA
3.0uA
3.8uA
Condition: Power Supply 3V Battery; Temperature 22...
Shalom!
We have a nRF9160 custom board on which I cannot switch some of the IO lines.
For example we have two leds, P0.9 an P.10 but only P0.9 works. The hardware guy...
Hi there, now I set up a BLE to connect peripheral to central via NUS service. The peripheral is a customize board with nRF52832 and the central is nRF52840 DK board. The...
Hello everyone I hope summer's kind with you (or winter, for the southern hemisphere...)
Here's the deal: my printf and NRF_LOG_INFO output zeros, while my register clearly...
Hi Nordic team,
I am using nRF connect sdk mesh light_switch example. version of sdk is v1.6.1 .
The node is detected in the nRF mesh app in my mobile.
what does group...
I believe I'm following both the Cypress data sheet properly. Yet I'm still having an issue getting the simple QSPI Peripheral example to show data consistency.
Can it...
Hello
I want to operate SSD1331 OLED(96*94) using sdk v17.0.2 and nrf52840 custom board.
The OLED example of sdk v15 was replaced with the codes of sdk17 and tested on...
Hi Nordic experts,
Recently, I consulted the datasheet and tried to find out something about the radio speed when using softdevice, unfortunately, I can't find anything...
We are in the initial stage of development of a product that will be shipped in different countries and different customers.
We would like to use an MFF1 or MFF2 eSIM for...
Hi
When trying to register iBasis sim with correct ICCID and PUK, I get this error message:
Username and pool information are required.
could You help me with...
I have my IMEI but my pin number has 4 digits: 0000, instead of 6 digits(which is required to add the LTE device)? Please Nordic, what should I do? I have this problem for...
I am a beginner in embedded systems.
I know that the minimum resolution of RTC is 1/32768, but what is the effective number of digits for this? For example, I used a counter...
