When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi,
I have my device based on the nRF52840 and it is working fine but we are focusing some issues given by our users.
When our device is connected to a smartphone, the...
Hi
I am having trouble changing the MTU size. I am using SDK 15.3 on nRF52832. I am developing a combined peripheral/central application, but I only need Data Length Extension...
Hi there,
I'm wondering if I need to have an SPM configure permission for my untrusted firmware to communicate with the environmental sensor via I2C.
I'm presently trying...
Hi,
I have a working project and want to use I2C 2 instead of UART 2. I have changed the .dts file:
/* &uart2 { status = "okay"; current-speed = <115200>; tx-pin = <29...
Just wanted to share my project of controlling the position of feedback servo motor with Nrf52840 by sending bluetooth commands using nordic toolbox
github.com/.../Feedback...
I used the mpu6050 sensor and did it according to 1.2 of this blog .
The driver of this sensor is in the ncs\zephyr\drivers\sensor\mpu6050 directory.Error after compiling...
SDK: NCS 1.4.0
board: nRF9160-DK
sample: lwm2m_client
# registration CoAP packet
In option enum, there is no "others". Where can I get this information?
I'm writing an application that transmits data over a mesh network of nRF52840 microcontrollers using OpenThread. I'd like the microcontrollers to prioritize sending MLE traffic...
I want to upgrade my application from v1.4.2 to v.1.5.1. but the Bluetooth init failed. So I tested with the scan_adv, which uses the same logic as my application. This also...
The device communicates okay with JLINK commander v7.00a although at the beginning it always says "Connecting to J-Link via USB...Out of sync , resynchronizing... J-Link communication...
Development Environment: icore7 laptop running Ubuntu 20.04.2 LTS.
Target: To build connectedhomeip sample application for arduino nano 33 ble board and check against laptop...
Hi,
We are building our project with nRF52811 and Segger Studio V5.34. (I have Ubuntu 1804 if it helps.)
We have certain variable configurations but would like the ability...
Hello Team,
My end goal is to send 0 to 600hz signal over Ble using NRF52832[ as explained below image].
So, for this, I have used this GitHub code
https://github...
Hello,
I am working an a product based on the NRF52832 and I need to trigger an interrupt when a capacitive button is pressed / proximity detected (BLE is peripheral and...
