Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello All,
I am implementing a simple UART bridge over BLE and want to add a Characteristic to update the baud rate being used. I thought I added code to support a new characteristic...
Hello!
I have this interesting bug with the twim driver.
It works perfectly with the NRFX_TWIM_XFER_TXRX transfer type: I see the transaction go out on the bus lines...
Hi,
My project uses nRF52840 with SD 140, SDK 17.0.2 and SES. My hardware has SD Card SPI and LCD SPI sharing bus pins, using CS pins to switch devices. Because of this...
Hi,
When I use Texas Instruments CC2650 MODA (using Bluetooth 4.2) as the the transmitter, a smartphone (iPhone or an Android phone) that has nRF Connect app as a receiver...
Are there any examples to program the nrf52 at a lower level bypassing all the bloat/ 10 layers of abstraction in the SDK? TIA.
I often hear that things were more straight...
Hi,
I'm using nRF52810 with custom pcb antenna.
When i scan my device using nRF52 DK and nRF Connect in windows 10, my device scanned.
But, when i scan my device using...
Dear All, i am using NCS v1.2.0 and the GNU ARM Embedded toolchain: 8-2019-update. I am able to compile and run programs successfully from the command line and SES, but I...
Large data volume communication appears SOFTDEVICE: ASSERTION FAILED error
However, using the same firmware does not have this problem on another board。 What causes SOFTDEVICE...
Hey Nordic Team,
I am trying to disable the SPI module to optimize my project and reduce flash usage. The Zephyr optimization guide refers to disabling unused peripherals...
We're beginning a design with the nRF5340 and are needing to make power architecture decisions. Are there efficiency curves for the internal regulators, in DC/DC mode, for...
I have an nRF 52832 running the SDK 15.2 as peripheral and have tried connecting to different Windows PCs: a laptop running a native bluetooth 5 adapter and a desktop PC running...
I'm beginner in the bluetooth environment so I don't understand everything in it.
For my project, I need to develop connection betweeen a BL652 and a smatphone.
In a first...
Hi,
For both (nRF52840 / nRF52832 ), with SDK version nRF5_SDK_15.3.0_59ac345
I am using Secure_Bootloader in the eample folder:
nRF5_SDK_15.3.0_59ac345/examples/ble_peripheral...
I found an issue when using CONFIG_AZURE_IOT_HUB_DEVICE_ID_APP to set the Azure Device ID.
Around line 88 of azure_iot_hub.c the "user_name" structure is set using the...
