Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
HI!
I use flash data storage (fds) to store some user inputs in flash. Everything works fine, but I am surprised by the fact that the function fds_record_update() is not...
Hi All,
Using SDK15.3, NRF52840 USB Dongle.
After a few experiments I would like to clarify my understanding on how the usb bulk write works.
I am currently writting...
I am using Nordic Thingy 91 Kit.
I have uploaded modem and application firmware URL : Nordic Thingy:91 - Downloads - nordicsemi.com
I am facing following problem while...
The following issue is for NCS version 1.4.0 and 1.4.1 for an nRF52840 DK target.
When CONFIG_BT_AUTO_PHY_UPDATE =y for both a peripheral and central, I see in Wireshark...
Hi,
I am using the following snippet in my application. it is working fine sometimes but the other times it's not coming out of the while loop.
can anybody point out the...
I have been struggling to reduce the current on the Nordic Dongle to the sub 3 uA levels that the specs suggest I should be able to achieve.
I am stuck at achieving a 9...
i am trying to determine the current consumption of the nRF9160 when in sleep mode but running LPUART and TWIS.
I see that the Sleep mode (MCU IDLE, MODEM off, RTC on) shows...
Hi all, i want to use CMSIS DSP library for vector/matrix computation.
In NRF connect SDK, there is a "nRF CMSIS DSP examples solution" in the dashboard, however it fails...
Hello,
I have an external flash w25n01gv, I am using this simple spi loopback example to test the spi functionality of nrf9160. I want to read the jedec id of my device...
Does doing DFU again and again on same controller can cause misbehavior of code? I am using BLE + UART + EEPROM in my code and sometimes I face the issue with UART event handler...
Hi,
I'm using NRF52840 to connect my mobile.
I'm using whitelist, following the example. It used to work perfectly for about 1 year.
However - in the last couple...
After starting the program, I do the first calibration and read the data 30 times. The standard deviation is between 2.0 and 2.3. Perform 30 "Calibration -> Read Data" each...
Hi,
Greetings of the day!
I used nRF Connect for desktop to program the nRF52840 device. But I can't lock the program and protect the device using this utility. I installed...
Hi,
I tried controlling the LEDs connected to P0.0, P0.7 & P0.11 by using
nrf_gpio_cfg_output(); nrf_gpio_pin_set();
nrf_gpio_pin_clear();
& ble_app_blinky example...
Hello,
My project application demands exchange the data from PC application(custom application developed by us) which is act as a server to the controller which is act as...
