Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
The specifications for Flash programming in section 4.3.7.1 page 21 is blank in the nRF52810 Product specification 1.0. Can you please provide the values for this table?
Hi all,
I am not able to update the modem firmware over usb/mcboot with the programmer on my Thingy91. I have tried both on linux and win 10, the problem is the same. The...
Hi,
I have been using the NUS on nRF52832 DVK with no issues, however, when I migrated to the nRF52840 DVK and a custom board based on the 52840, the NUS characteristics...
Hello Nordic Community,
I am currently following the SMP guide provided here: https://docs.zephyrproject.org/latest/samples/subsys/mgmt/mcumgr/smp_svr/README.html
The...
Hey,
I am wondering if it is possible to run MTD and SED on the CoAP server on nRF Connect SDK v1.4.0.
I have looked at the question " How do I set up CoAP Server whit...
Hello,
We are going to design our new product using NRF52832. Please suggest if there is any other better IC which has higher transmission range, higher RAM and with less...
there is a module in the skylab project on the nRF52832 chip and it does not agree with the tablet, which is old BT. Is it possible, through the firmware or SDK, to downgrade...
Hi
After nRF Connect for desktop was upgraded to v3.6.1, programmer application cannot recognize all DK boards, including PCA10040/PCA10056/PCA10090.
It showed the error...
Can I use nRF21 in GPIO mode (not SPI) using the PA/LNA assist feature of the S112 soft device?
Per section 5.3 of the datasheet, it seems I could wire the PDN pin to be...
Hi,
I am learning how to write and read from flash memory on nRF52833 dev board for a BLE application.
I followed the heart rate example as shown in https://devzone.nordicsemi...
I am writing an application for the nRF52DK which uses two additional push buttons besides the 4 already present on the board.
Using GPIOTE the detection of the button press...
I have a working project that uses the NRF_LOG module to send debug outputs over the UART backend. When just using the logging module everything works correctly.
I added...
Hi,
Is it possible to set multiple APNs in nrf9160 and with fallbacks to next APN if one not working?
Suppose if we set 2 APNs at CID=0 and CID =1 positions using AT+CGDCONT...
