Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello,
I am developing on the NCS 1.4.0 and on a NRF9160DK. I am working on the asset_tracker example and I noticed that the code sends an assisted gps request to NRF...
Hi,
I am using app_uart library with Tx and Rx FiFo. I want to check how much space is available in the Tx FiFo at any time, and similarly how much space is filled in the...
Now I am using Nrf52832,SDK15.0.0, S132,
When we developed the DFU OTA function APP, we encountered some abnormal situations: it could not get out in the bootloader mode...
HI,
I am trying to read the payload length of the data coming in a topic via MQTTSN over OpenThread. In the event handler, I am getting the event and trying to get the length...
Hello everyone
I am having a problem with the nRF Connect SDK 1.3.2 and the bluetooth peripheral UART sample on the nRF5340 PDK. The programm compiles and runs (the chip...
Hello,
i am using the DWM1001 Board with the nRF52832. I was curious if there is software similar to CubeMX for this MCU on this board.
So far I have not beed able to...
Hi,
I want to set two nRF52 modules pairing with each other.
During the pairing process, authentication is also needed for the sake of security.
The firmware I used...
Hi,
I want to use the nRF5340 for a project that will use direction finding. I want to know if the Nordic nRF5340 SoC is compatible with Bluetoothe devices form other companies...
I used NRF52832 before, nRF5_SDK_14 for the software, using the ble_app_hrs_rscs_relay example in the SDK, NRF52832 as the host to connect a heart rate wristband, and then...
Hi, hope you everything goes well.
I have a question about using the CT008-U LCD, with nrf52840. And I am going to use gfx class function to write text or draw a rectangle...
Hi, I have interfaced the nRF52832 with temperature sensor via i2c(MAX30205 temperature sensor) . I am advertising only when it become low temperature( setting the threshold...
Hi Devzone:
I want to make nRF52833 chip enter sleep mode but not deep sleep(SYSTEM OFF) so that real time clock can still wake up the system. We don't use softdevice. ...
