There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi,
I'm working with the nrf/samples/nrf9160/at_client (@ tag v0.3.0) with a PCA10090 board.
I had a question about the response to the AT+CESQ command.
Specifically...
hi,
i am quite new with programming tools like the nordic thingy and i am currently trying to get some initial program running, i.e. the blinky example. i have a few questions...
I am converting the simple_on_off vendor model to send a message on mesh 3.1.
the server implemented the simple_on_off model successfully. But but my client runs into 0...
Hi currently I am using the nrf_mesh_sdk_3.1 latest release light_switch Example both client and server one after successful compilation and load examples in DK boards when...
Hello,
I have updated secure_boot to allow UART3 to be used in the non_secure area. However, as soon as I try to initialize it in the non_secure area a hard failure occurs...
Hello! I took the example of "usbd_cdc_acm" and added a receive and transmit buffer. The data from the receive buffer is sent back. It turned out that the first byte is written...
Hi All.
I have a project where my peripheral (nRF52832) connects to my central (nRF52840), and then transmits 128 byte packets continuously one after the other. It works...
We are using the nRF9160 DK with the Asset tracker example, which is working in combination with the nRF Cloud.
Now we want to use our own AWS account in combination with...
hi all i am trying to read data from a sensor in burst mode i can"t able to read all datas from the register .I tried to read the data in both spi and spim(with easydma) ...
Hello,
So I'm using nrf52832 with sdk15.2 and I'm trying to connect a joystick to the adc pins and have the joystick to move the mouse instead of the buttons and having...
hi.........
i am tried to merge the blinky and timer sample program , i am getting this error , even i have included all files .h , .c files
nrfx_config.h: No such file...
Hi
I am using nrf51822 chip to develop my application & I need to put the hardware into sleep. In which all the gpios & other peripheral goes stop to save power.
SO, how...
Hi,
I want to change MAC address during advertising in nrf52810.
nrf52810 receives MAC address via uart from other MCU and set this MAC address. (type is BLE_GAP_ADDR_TYPE_PUBLIC...
We're building small robots/toys that work with each other.
Would it be possible to use the nfct on two devices with nRF52840 to communicate between each other?
Also...
Hello,
I’m sorry for asking again, but I could need some help again. This is a followup to devzone.nordicsemi.com/.../missing-endcrypt-event.
I’ve managed to receive...
