Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi,
I'm trying to build the Serial LTE Modem in my nrf9160 SIP custom board to communicate the STM32 MCU with the nrf9160 using AT Commands via uart.
My physical connections...
Hi,
I created a custom service in accordance with NUS service. I am able to assign all handles, subscribe to notifications. But I am not able to read any data from the device...
Based on my understanding on SPI signal, CS/SS pin need to pull down to low when read/write and pull up high when the action is finished.
May I know if this feature has...
I'm currently working on a project that uses the MLX90640 IR sensor. By default, this device has an I2C address of 0x33, but it can be set up with one of 127 different I2C...
Sifting through previous posts about redirecting printf to uart by using retarget.c, I have found this will work on previous versions of segger (5.42). Has anyone gotten it...
I tried adding the following settings to prj.config
CONFIG_CHIP_OTA_REQUESTOR=n
CONFIG_CHIP_QSPI_NOR=n
I've also tried to modify the Devicetree to be the qspi part in...
Hello, I have a project sampling a ADC. It has a INT output signaling new data is ready to be read with max sampling rate of 125ksps. I am using the interrupt and then reading...
Hi community,
I'm making a custom board using the NRF52840-CKAA. I'm trying to make a Bluetooth application for this board but struggle to achieve it.
setup:
- Visual...
nPM1300ek version: 0.9.0 I have both "nPM Controller" and "USB PMC" USB connected. I tried powering USB PMC through the computer and also tried a "Wall Wart USB".
I have...
Hi,
I have a device which has different UUID s for the write and read characteristics than the Nordic devices. The device I want to connect to will give out sensor data...
hi,
I am in the process of creating a board definition for a custom hardware we are proptotyping. I follwed the instructions in the intermediate course, copying the nrf5340dk...
I have a device which advertises some services, I want to discover those services and write to those characteristics. However I can only find one service and not multiple...
Hello,
I want to send audio to multiple headset(Readily avaiable from market), So is there any hardware, Software solution avaiable for that.
So, Is there any...
We've had good success measuring power consumption with the PPK2 until now. But recently, it started reporting some hard-to-explain numbers. Specifically, t told me a nRF9160...
Hello everyone,
Im currently using the Thingy:91 with the asset tracker v2 application. As I understand the default mode in this application is the passive mode. Im measuring...
