Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Since https://github.com/nrfconnect/sdk-nrf has disabled issues, this is an assorted list of problems/limitations with the lte_net_if library ( https://github.com/nrfconnect...
Hi All,
I want to do dfu over uart with secure bootloader, am using nrf52840-DK, nRF5_SDK_17.1.0_ddde560 SDK and segger embedded studio V8.10.
compiled and flashed secure_bootloader_uart_mbr_pca10056_debug...
I use DWM3001C chip,it has a nrf52833 mcu inside.when i call ble_init() in main.c.it report error:
peer_manager_pds: Could not initialize flash storage. fds_init() returned...
Hi Team, I'm trying to port the acconeer project that worked on the old one NCS v2.2.0 to new NCS v2.5.2 and ran into a problem with the difference
c:/ncs/toolchains/c57af46cb7...
I am trying to use libmodem in a bare-metal app on a 9151dk, but nrf_modem_init() is hanging (not returning). What conditions can cause this? The issue looks a little like...
Hi there.
Right now, I'm facing the issue that I want to use the camera OV7670 with the nRF52833.
I don't know how to start or what example I can take as a base to start...
Hi,
I am using EVB of RAYTAC MDBT50Q-DB (nrf52840 module) for power consumption testing,
I'm running a zephyr application on it, to debug power consumption issues, using...
I have an application where I would like to use ACLK at 12.0 MHz to drive the I2S MCLK signal and create an atypical audio sampling rate (46875 samples/sec). If ACLK is at...
Hello!
Using SDK v2.6.1 and the nRF5340 Audio application, I want to use an external button as button5 instead of the one that is on the board.
I noticed that if i change...
Sometimes I just want to compile a single file for an nRF Connect project with VS Code and the nRF Connect extension. This sometimes fails because an include file isn't found...
Hi.
I am updating an nrf9160 B1 project on a custom board in SDK 2.1.0 to SDK 2.5.3, and I am running into a problem when building. This error does not show up when building...
Hi,
Hello, I have a project that's working great but now I want to extend the abilities of the device by using the extended PHYs. I know there are a so many threads on this...
Hi DevZone!
I'm currently developing a device that has several hardware actuators and I've implemented 2 OnOff Models each belonging to an element. But right now I'm having...
Hello there!
I'm trying to enable secure boot via CONFIG_SECURE_BOOT and am currently getting the following error:
I'm using zephyr via sdk-nrf v2.6.1
Searching the...
Hi,
I just try to use the DFU over USB to upgrade the FW but i found one problem which is the process will erase the external flash data
but i put the some sensor FW data...
