Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello,
for some time I didn't have to work on my project that uses nRF Connect SDK but recently I had to work on it again and noticed that I am not able to build my before...
Hi,
I am trying to create a trilateration system with 3 initiators and 1 reflector (Hopefully multiple reflectors in the future) on the nrf54l15. The channel sounding with...
When running the NRF Connect SDK SoftAP sample, connected stations disconnect at **exactly 5 minutes** (300 seconds) into the session, regardless of activity or configuration...
Hello support,
For our project we have an integration with Memfault for metrics, coredumps and log files.
We are currently developing in NRF 2.7.0 on a nrf9160 chip. ...
My SPI slave sensor requires a 32-bit frame length. The CS (Chip Select) signal needs to be switched for each 32-bit frame interval, and it also supports DMA (Direct Memory...
Hi ,
I am using skb501 module and which contains nrf52840.I am using nrf5sdk for development for zigbee coordinator because nrf connect sdk is not supportable in this...
Hello!
We are developing a device based on the nRF5340 and using SDK v2.6.0. The firmware implements a USB composite device (CDC ACM + MIDI + Audio). Everything works perfectly...
I am attempting to interface a tas2110 with an nrf52840. I just became aware of some nrf52 limitations and wanted to get the latest info. My requirements are as follows "The...
as shown in this document:
https://www.bluetooth.com/wp-content/uploads/Files/Specification/HTML/Core-54/out/en/host/attribute-protocol--att-.html and Zephyr's att.h , 0x0d...
When I run the peripheral_hids_mouse sample, I scan/connect on nrf connect and see an instance of the peripheral. then if I clear and scan again in the Discovered devices...
The J-Link itself can’t “see” the external flash — it only talks to the nRF5340’s CPU via SWD. I would like to program initial image of the external flash. 1. On Segger website...
Hi,Team,
I'm currently using the nrf54l15-dk. I want to implement our custom app to send firmware data to the nrf54l15-dk, have the nrf54l15-dk receive the firmware data...
Hi, I have two nRF52840-DK boards and I'm testing matter light bulb example.
If I load the project in one board it works fine when I link it with virtual assistant like...
Hello,
In my application (nrf52840, v. sdk 3.0.2) I have a partition named "settings_storageuser", which is defined in the internal flash using partition manager and that...
Hello,
whenever I try to debug my nRF Connect SDK application, I have problems with the nRF Connect for VSCode debugger in such an extent, that I can't use it.
When I...
