I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hi,
I have a custom board which uses P0.02 and P0.03. They are connected to interrupt signals from external devices.
To configure them as GPIO I set CONFIG_NFCT_PINS_AS_GPIOS...
Hi
I am developing a custom board using nrf9160. But before jumping to that process, I am using thingy91 (nrf9160 chip) as evaluation board for check all the firmware works...
Does ZBOSS support manufacturer specific attribute extension to standard clusters?
How about implementation of manufacturer specific clusters?
Are there examples one can...
Hi,
iOS NRF Mesh 2.2.3 version is working, but 3.2.0 unable to connect nodes,
Please suggest the procedure with iOS version in details.
Regards,
ArpitA
I use nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac and pca10056 board.
I use project nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\examples\zigbee\light_control\light_bulb...
Hello! I will start by saying that I am new to embedded software development, and new to nrf boards in general. After successfully running the direction finding connectionless...
Hi Nordic Team,
I got the board yesterday, so I tried to debug on it. it seems no image is downloaded before shipped to me, as no log at all after power on, right?
So...
I have the next system perfectly working:
nRF52840 working as NCP to get OpenThread protocol.
STM32L486 as a host with a FreeRTOS
The communication between both is...
As far as I can see, when sending data via Bluetooth, the data is first stored in the buffer and then sent out together when the buffer is full. Is this the right idea? But...
Hello, We have an nRF9160 based IoT device in the pipeline, which should now be tested in a certified test lab. The purpose would be to perform a spurious emissions test using...
Good Day
I have enabled power saving on my nrf9160dk and am using NBIOT. In doing so I found that there was a 60 sec offset to what I selected and what I wanted the active...
Dear: IC : nRF51822_xxAA SD: s130_2.0.1 BL: SDK12.3 bootloader_secure with public_key AP: NUS MOBILE: iPhone 13 pro MAX with iOS 16.1.1 not always fail. but often How can...
Hi,
I'm working on a legacy program using nRF52833 and nRF5 SDK using SoftDevice S113.
My application has two input GPIOs, and both can wake the MCU from System OFF. The...
Hello,
My professor bought several nRF9160 boards for our Electrical Engineering department to work on our final class project with. Several students are having a hard...
