hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
Hi,
In our PCB using the nRF54L15, we used different P2 pins for the sQSPI, believing after reading the docs and driver API, that one could configure different pins than...
Hello,
I have some trouble to identify my custom nrf52832 board in the VSCODE.
To program the board I am using nrf52840dk, and connect it to my board as follows:
...
Hello Nordic Support Team,
I am testing nRF9151-DK board. I wanted to debug an application that is created when "Create a blank application" option is chosen from nRF Connect...
Hi everyone,
I am trying to use P0.0 but it keeps getting uninitialized when calling nrfx_spim_uninit.
nrfx_spim.c line 659 keeps uninitializing P0.0
It is because...
Our device is using NRF54L15 for BLE function. When we test the max distance of ble connection between 2 devices, we get the below results.
We are confused by these...
Hi Nordic Team,
I am working on a custom device based on the nRF5340 SoC . My application captures live audio from an I2S microphone , processes the audio on the nRF5340...
Goal: Create SBOM with correct version numbers, CPE search strings, PURLs, and licenses. Use that to scan and assess vulnerabilities. Platform: NRF Connect SDK 2.9.1 or newer...
we run long-term HIL tests with typically 3–8 nRF9151 DKs:
DKs spaced only about 1–3 cm apart
short USB 3.x cables to powered USB 3.2 hubs directly below them
sometimes...
This is a product based on nRF52832, which uses PA/LNA.
The device resets in Bluetooth advertising state. the ID is 1 (NRF_FAULT_ID_SD_ASSERT), the PC is at 0x000071CC,...
Hi Nordic,
We are developing a PC application for product programming that uses nrfutil to program the nRF54LM20. The programming process involves recovery, programming...
I understand that the NRF54LM20 reference suggests not to put any sort of resistor or capacitor components on the reset pin and simply rely on the internal pullup. Since this...
Hello,
We're trying to build a demo based on the BLE Audio sample with extra BLE services to transmit sensor data.
I have managed to build and run the BLE Audio sample...
Hello,
I am using the nRF52840 DK (same applies also for the dongle). The setup is quite simple. I have two nodes on my desk, one transmitting packets and the other receiving...
Dear NCS team,
I am developing an asynchronous UART driver using ncs v3.1.1. I observed that when calling uart_rx_enable() with a timeout value of 100 µs (at 115200 baud...
I am using OpenThread Secure CoAP with DTLS/PSK on an nRF54L15 DK.
Environment:
nRF Connect SDK 3.4.0
Zephyr 4.4.0
nRF54L15 DK
OpenThread Secure CoAP API ( otCoapSecure...
