Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hi,
we want to use distance measurement sample in nrf5340. The webpage for the example says that it supports nrf5340. we are getting error, when we try to build the sample...
Hello,
I have the Audio DK, and evaluated it as suggested, However now i am now trying to connect it to a Android Phone to evaluate it in a more realistic scinario.
Does...
Hi all.
After finishing some test I want to generate the binary for the MCU nrf52810 using zephyr. I have look in the zephyr folder and saw the zephyr.bin file. Is that...
Hello,
I'm currently developing with a nrf52832 (QFABB0) and I have to use pins 16,38,37 and 17 as gpio.
The problem is that when I have an error for pins greater...
Hi Nordic team
Q1. According to nrf Connect SDK documentation, Zigbee and Matter samples all supported FOTA (firmware update). Where can I find the DFU samples for Zigbee...
Hi，
When the friendship node has established with the LPN node, how to verify that the friendship sends a useful message to the LPN node?Has it any API to verify the message...
Hi If I permanently see 3.3v even when the application is not running does that mean it is busted? I also see a lot of spikes in the output I have placed an order for another...
Hi.
I have a problem using dfu bootloader.
SDK : 17.1.0
SD : 7.2.0
device : nrf52840
dfu code : secure bootloader pca10056_s140_ble
uECC : 13.0.0
I implemented...
Hi Team,
I am working on NRF52832 based on the BLE mesh protocol here I am using the Light_switch example of SDK - nrf5sdkformeshv500src
Here I need to detect and monitor...
Hi,
I am using a Raytac MDBT50Q module on a custom board of mine. I have no 32kHz installed (which is available inside the module), VDD and VDDH are common and powering...
I'm porting code from my device which uses the nRF52832 to the 840 DK. My general process was to get the code developed on my own device to run on an 832 DK, then an 840 DK...
Hello everyone, I'm new here, and new to using the Nordic boards. I have a question regarding the RF connector in the nRF52840_DK. I am trying to do some RF measurements with...
Dear Team,
We notice that systemOFF current varying from 220 nA to around 500 nA for different devices. For some devices we are able to achieve 300 nA as mentioned in the...
Hi,
I'am using the ble_uart example on a custom board, where I have the issue that the BLE advertising is only available after a reset OR when I comment out the uart_init...
