Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I following description of https://github.com/NordicSemiconductor/pc-ble-driver#Compiling-pc-ble-driver-from-source to build pc-ble-driver
pc-ble-driver\build> cmake -G...
Hello,
I'm trying to determine the actual used data rate for the coded PHY but cannot find the corresponding API / data structure / enums.
Am I missing something? Can...
Hi!
I have the Actinius Icarus board pre-loaded with the Actinius asset tracker firmware.
Lets say I instead want to load the Nordicsemi asset tracker firmware on the...
Hello,
We have been having strange issues with the watchdog on some of our development devices. The issue is that it seems the watchdog will sometimes not properly reset...
Hello,
I'm currently trying to convert the SPI example project for NRF52811 for the EVK BMD-360 and ran into an issue.
I'm using segger embedded studio 5.42a and nrf sdk...
Hello Nordic Dev Zone,
I have been developing on the nrf5340pdk and recently switched to the nrf5340dk.
I utilized the COM console output for app/net cores via the `minicom...
Good day,
I have successfully implemented exercise steps 1 to 5 of Exercise 2, Lesson 3 of the DevAcademy "nRF Connect SDK fundamentals" course, that deal with "adding custom...
Hi,
As i2c communication + computation takes 45ms in my timer interrupt that happen each 100ms and gave issue with SD, I decided to set a flag in the interrupt and execute...
Is there a configuration / sample available of mqtt simple to talk to the mosquitto server using an authenticated client on port 8884? I saw a message on here that was about...
Hi,
I want to get the GPS value from A- GPS continuously.
Meanwhile, if there is any new application firmware version update,
I would like to download the image with...
I see the problem here. use the dfu-util command in the window system
and i tried many methods and failed The following is my reference website
http://zadig.akeo.ie...
I've been playing around with some code that puts my hardware into System OFF mode to save power, and then will exit this mode and start up when one of three different GPIO...
Hi,
https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink
I have tried the example you modified. It works fine. However, I get ERROR 17 NRF_BUSY when 2-3...
Excited to have ordered my BLE Audio DK which uses NRF5340.
In my use case I am looking for many microphones (audio transmitters) to a single listening device (audio receiver...
