Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
I am testing out the nRF Cloud MQTT multi-service example on my nRF9160 DK board. When looking at the GPS data on the cloud it is not very accurate and does not track my location...
Hi!
I am experiencing some odd behavior from the modem, and I hope you can help me understand it:
After I disconnect from LTE using lte_lc_func_mode_set(LTE_LC_FUNC_MODE_DEACTIVATE_LTE...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with a connection to an external MCU (#define MQTT_MESSAGE_BUFFER_LEN 8192) We tested...
I have not been able to create a stable development environment in macOS Monterey using the automatic installation process.
In order to better understand and document the...
Hi.
I'm working on a project based on the USB CDC ACM sample from Zephyr, which builds correctly for nRF5340DK, but gives an error when trying to build for nRF9160DK due...
Hello,
I am working on a project based on the nRF52810 custom board, I need to use several slave nodes to communicate to the gateway node/ server.
I need to improve...
Hi,
I want to use the nRF9160 SiP to connect via NB IoT to AWS IoT server but I don't want to use any SDK, I only want to use AT COMMANDS, there is some process that I could...
Earlier I created a project in SES for nRF5340. The simulation and debugging was quiet simple and easy to find the fatal errors, run time errors etc. Same features are not...
Hi,
I working with NRF52840 DK board, I need to read some potentiometer values from 0 to 10 using ADC with ble_app_uart. I have combined SAADC code and BLE_APP_UART code...
Hi,
Due to shortage of pins SPI CS is reconfigured as GPIO while SPI is not used. Soft device is not used.
Problem is the delay that is needed after nrfx_spis_uninit call...
Hi !
I use the NRF52832 and with Segger Embeded Studio to code.
The problem I have is that for some reason, my uart don't work after using an I2C write protocol and I...
Hi,
I tried to send a packet larger than 20 bytes by calling bt_nus_send on peripheral_uart but failed.
After checked on DevZone, I found some similar problem and did...
We are having connection problems with our nRF52832 based HID device only on Windows. I've attached packet captures taken with the nRF sniffer (nRF52 DK) and in Windows with...
Hi,
I looked at some of the questions on the forum and they didn't give me good advice. Currently all I can do is nrf52832 Security 1 Level 4 and nrf52833 Security 1 Level...
Hello
I try to write functions to modify the publish and the subscribe addresses. Unfortunately not all is working, attached you will find my code.
Problems:
1.pubish...
