Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
I tried to create/ open a project using nRF Connect in SES. The error appears as shown in image. While the file exists as shown in the second image. Why, such error and what...
Hi,
Basically, the setup of the mesh network is as follows,
There are END NODES based on sensor server model.
There are RELAY NODES based on the sensor client model...
Hi,
I am using Zephyr3.0.0 to validate AOA CTE sampling.
Firstly, a s below is the official data format. Nordic Semiconductor Radio peripheral provides 16 bit wide IQ...
Hi,
I am able to successfully build and flash the Matter Light Bulb sample onto my nRF52840 DK.
I am now getting ready to configure the firmware for use on a custom board...
Hi,
NCS1.9.1,nRF5340DK, VSCode，
see code, timer_lms==1000 spend 1000ms
but if start i2s
i2s_audio_init(); //this line will Slow down the time
timer_lms==200 spend...
When i try to use SES to build my project.there is error.The enviroment i confige as descrblied. them i use toochainmanger in nrf connect tools,the error is as the same as...
I'm trying to determine how to get a Linux timestamp for a project using nRF9160. It looks like the mktime() function is not supported. Any suggestions?
thanks!
I'm running into a weird bug where the first 4 bits received by my SPIM are always 1 - the next 64.5 bytes are all correct though... I've built 3 FWs out of provided examples...
Hi guys,
I have developed an app to read data from some sensors and notify the central with a frequency of 100Hz. It seems to work but I would like to share my approach...
Hello,
We are trying to get UART communication between nRF9160 and MSP430.
MSP430 need to send out a sensor data through UART.
We are using 1.9.1 SDK, and Visual...
Hi,
Is it possible to remotely execute a command that would force a BLE node into indefinite sleep or standby mode?
I am working to build out a BLE mesh network, where...
Hi. We have a custom board featuring 4 FSR sensors on it, based on the Nrf52810. Initially i tested those boards and the sensors using an STLink-V2, along with the Arduino...
hi thanks for you heip!
i want use \nRF5_SDK_17.1.0_ddde560\examples\peripheral\radio_test for radio test, here is the questions:
1、could this example can send prbs9 wave...
Hello!
I have to decode signals from two quadrature encoders. I know nordic has a driver for this, QDEC, however. there are a couple problems:
1. I need to control two...
