hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello,
I am trying to set system on mode in nrf52840 usb dongle.
This mode switched automatically by idle task, when there is no thread running.
There is no while(1...
Hello,
I m new to nordic in VS code. Bought two nRF5340 DK for ADC conversion and wireles data transfer.
Followed all Youtube install instructions "nRF Connect for VS...
Is it possible to communicate with the of nRF52840 through USB, for example using PyUSB?
If yes, is there any documentation that can help in this regard, e.g. documentation...
These are Central device 52840 settings:
These are peripheral device 52810 settings:
I use official sdk16.0. Central Project is ble_app_multilink_central...
HI,
I am designing a costume PCB of nRF52840-CKAA-R7. I used Johanson 2450AT07A0100 Chip antenna for BLE, please suggest the matching circuit for it.
Due to size concerns...
Greetings. Like some others, I recently tried to activate the iBASIS eSIM included with a nRF9160 DK and found that the SIM had expired and could no longer be activated. I...
I found that one via on nrf5340dk is different from other vias. It has an extra loop and is connected with the external copper layer. What is the purpose of this design? How...
Hi,
Firmware with changes from hci-lpuart sample code is terminating abnormally. hci-lpuart sample code is modified to call "adc_read()" method to read adc values. When...
Hi,
I am using sprintf to copy floating sensor data to a string and later copy that string in payload.
But when I do so, floating number is not copied, but rest of the...
1). want to know what is the sacn interval/window value used in wireshark
2). how many max. number of advertising devices wireshark nrf sniffer displays
3). instead of...
Hi everyone,
i wrote a dockerfile with all nedeed dependencies and toolchain setups for software development of nRF9160DK. I would link to use Visual Studio Code running...
Hi Team,
We have a case open - 285055 - where we raise issues about some data being rejected from your nrfcloud platform. As a secondary investigation we are looking at...
Hi, I've just read this allocation guide and I was wondering what the "PH" in RAM_PH_START, RAM_PH_SIZE, FLASH_PH_START and FLASH_PH_SIZE stand for.
In which way do they...
I testing asset_tracker_v2. I observed that during debug, the execution enters the init.c file. As well __pinned_bss, __boot_func etc are used in this file.
1. What is purpose...
