Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
This is in reference to the note in the manual that says:
6.14.11 Battery protection If the antenna is exposed to a strong NFC field, current may flow in the opposite direction...
I can not get the SPI Slave function working on nRF52840 (nrf52840dk_nrf52840 board)
In the nrf52840dk_nrf52840.overlay I wrote: &spi1 { compatible = "nordic,nrf-spi"; label...
I have a number of devices that currently have an S132 softdevice, USB enabled DFU bootloader and application.
I am intending on updating the application, which removes...
Hi
I am now trying to add the light lightness model to the light switch sample code in order to use both the light switch and light light lightness features.
After adding...
I am using nrf sdk v_17.0.2 soft device s132
my query is for connected mode.
My project uses nrf52832 SoC, SHT4 temperature humidity sensor, 2MB flash memory.
it advertise...
Hi everyone, I’d like to build native code on my Arduino Nano 33 BLE on a Mac, i.e. using the nRF Connected SDK and avoiding the Arduino Core/Mbed OS. I’ve followed zephyr...
Hi All,
I have successfully used notify to transfer 1 byte of data.
Now I want to try to transfer 1 array but I have a problem as shown in the figure.
Here is my...
I try to get the BLE OTA procedure working using the nRF52-DK board.
1. Using the pre-build example hex files in folder "nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_dfu_test_images...
Hello everyone
Currently I am developing the code for a gateway that collects data from various BLE devices. Some of the peripherals go onto pairing process, meaning that...
I was wondering if there was a JSON formatter that could take a string and convert it to proper JSON. I checked the cJSON library and it seems to only be supported through...
Hello,
It is being developed using nrf52833, SOFTDEVICE-s140, SDK-17.1.0.
There is no problem in port-0 during I2C communication using twi_sw_master.c
,but when...
Hello everyone,
In the scan.h file of the scan module there is the following function declaration:
I wanted to use this function but during compilation I got the error...
I want to use an nrf52805 in a central role (only 1 peripheral connected).
Softdevice s122 appears to be small enough but the nrf52805 is not listed on this page ( https...
I build example in gzll_ack_payload folder get error:
.\_build\nrf52810_xxaa.axf: Error: L6366E: nrf_gzll.o attributes are not compatible with the provided attributes ....
I run newest nRF53 chip as of writing with 1.6.0 nRF Connect SDK from nRF Connect Toolchain manager 3.6.1 using SES 5.50c.
I use a array of 5 rx-buffers (Increased from...
