Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
I am using nrf52832 DK.
SDK 17.0.2 softdevice S132.
I am using freertos and running nrf52832 as a peripheral.
I want to put nrf52832 in sleep mode.
I am new...
Hello,
I am migrating code from nrf5_SDK_17.0.2 to nrf connect sdk v1.6.1. The board i am using is nrf52dk(nrf52832) connected with adafruit LSM6DSO.
Everything works...
Hi,
How can a specific folder structure can be realized in an SDK project.?
We want to create some folders and follow folder structure in nCS example and develop our...
Hi,
I am currently working on buttonless DFU for my application and I encountered a problem when I generated the .zip file.
In this line
--sd-req, in this case...
I wanted to send 'zdo mgmt_lqi 0x0000' through the serial port to get the 16-bit short address of the ZigBee terminal device, but I found that I did not return the value for...
Hi,
We are planning a product with BLE mesh capability using nRF52840 and a few sensors. The system power is from 2 AA batteries. We have 2 configurations in terms of power...
1) I am connecting dongle to laptop and selecting the device in nRF Connect App 2) Selected recently generated .hex File for example BLE application code 3) nRF52840 Dongle...
Hello,
we have a system utilizing a nrf52840, running a S140 softdevice and nRF5 SDK v15.0.0. We are already on the market and currently do only support android. Till...
hi,i have met some strange problem about inv-esb
i send 21 length packets in peripheral(i use rx as peripheral,use tx ascenter),but ireceive 0 length packets in center....
Hello, how do I configure the prj.conf file and the overlay file and how do I read the AIN7 analog input (P0.31) of the nRF52832. It is the first time that I use the micro...
Hello,
I am experiencing the following issue:
When trying to use the nrfconnect - bluetooth low energy app to configure my nrf5340 PDK, the connection to the board via...
I want to be able to flash (hex files) my Raspberry Pi 3, I am using Raspbian as an OS and I son't seem to be able to install nrftools for Linux on my Raspberry Pi. Are there...
I am building a product where a central device communicates with peripheral devices in a star topology. The main purpose of the communication is for the central device to...
