Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hey all,
I've run into an interesting situation where writing multiple notifications to successively to a multi-characteristic (custom) service causes data loss. Look like...
I updated nRFConnect from 3.6.1 to 3.7.1 and it started to have intermittent issues with the following error:
---
15:34:27.142
Application data folder: C:\Users\User...
To the kind attention of Nordic support team,
Let's take this as an example:
static inline void usbd_errata_187_211_begin(void) { NRFX_CRITICAL_SECTION_ENTER(); if (*...
As a test of how to add a library to a project, I am trying to add access to this library http://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.5.0/nrf/include/dk_buttons_and_leds...
Hello,
I am currently developing using Zephyr/NCS an application that supports FOTA/DFU.
The device needs to be tapped to be woken up and start advertising. So, when...
Hi, I want to build a Bluetooth LE peripheral application with nRF5340. The channel must be able to sustain an output stream of 8 kbit/s.
Other desirable features are: ...
GPS sample stops updating timestamp after a few days of uptime indoors
Tested devices: Thingy:91, nRF9160dk Tested firmwares: mfw_nrf9160_1.2.1, mfw_nrf9160_1.2.2
Demo...
I have a nRF52820-DK evaluation board which I am trying to develop on. I followed the manual install procedure on to my xubuntu Linux desktop. I followed these instructions...
Hi ! I have configured Zero bit length of S1 in radio packet ( nrf52840 ) but it is still mapped to the RAM.
... ((NRF_S1LEN_BITS << RADIO_PCNF0_S1LEN_Pos) & (RADIO_PCNF0_S1LEN_Msk...
We would like to use Zigbeee on the nRF52820, however, it seems from other threads that neither the "nRF5 SDK for Thread and Zigbee" nor the "nRF Connect SDK" support it,...
Hello sir,
I am using nrf52832 soc with customized board having gpio pin with P0.2,P0.3 and P0.4 used for led blinking for different purposes.The function used for led blinking...
Hello,
I have a problem with the SPI of the nRF52DK 52832, and Zephyr 1.6.1. I have to transmit 10 frames of 5760 bytes each to the TFT display with the ST7789 driver. ...
I am just creating this issue as a bug report. (my github issue: https://github.com/zephyrproject-rtos/zephyr/issues/38688 )
There is currently a bug in zephyrs handling...
Hi!
I had some time with the Thingy:91 and was able to get my own application running on the device using the nRF Connect Programmer application. To eliminate the need for...
