hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi，
I am doing a micphone " sph0641lm4h-1 ", and I use api of nrf_drv_pdm .c,
when I read mic data from sph0641lm4h-1 , they are just sets of 16 bit data, the following...
Hi. Thank you for your interest in my writing. I'm working on the IOS and the Multiple Connection project at the experimental_ble_app_multiperial example. It's a project that...
Hello,
I have been using the TWIM peripheral of the nRF52832 (via the twi_mngr) to talk to an accelerometer and a magnetometer. I have 4.7k ohm pullup resistors (in parallel...
Hi,
I am using nrf52840 customized dongle in our project. We have interfaced ADS1118 using spi communication with nrf52840 (customized dongle). The problem here with the...
I am trying to build the 'BLE NFC pairing reference' example for nRF52840.
I downloaded the latest SDK and located this example in the experimental directory under BLE\Peripherals...
nRF52840
SDK 15.3
Segger Embedded Studio
I PWM a piezo buzzer (with a transistor) , using the PWM peripheral. The problem I encounter is that before I call the PWM...
hi support team,
i have a wired problem that i can't explain to customer:
first, i test this project "nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_hids_keyboard...
I was able to successfully use the example ble peripheral blinky firmware example with the blinky mobile app. I added peer manager for passkey pairing but the blinky app is...
Hi Nordic Team,
I am using ble_advertising_advdata_update() to update some of the advertising data. I am doing every time the device is asked to advertise. In my code I...
the following report map is working when i try to increase volume on windows system (send 1 byte == 0xe9)
0x05, 0x0c, // USAGE_PAGE (Consumer Devices) 0x09, 0x01, // USAGE...
Hello,
my question concerns the layout of a bluetooth antenna & tuning circuitry for an nRF52832. Specifically, about two separate concerns:
1) Due to the shape of the...
Hi,
I want the received the datapacket from bluetooth to be stored in eeprom and access it when need be .If you have any small exmple codes for the same kindly inform me...
Hi,
We are migrating code from NRF Connect sdk 1.3.1 on nRF52840 to NRF Connect 1.6.1 on Nrf5340. Using SoftDevice as BLE controller on both.
Our existing code uses a...
Hi,
I want to run my application on the latest open thread libraries.
As per the page "infocenter.nordicsemi.com/.../thread_ot_libraries_building.html"
we need to run...
Hi,
We are using the nRF52840 Dev Kit with SDK17 and SD140 without FreeRTOS. There has been discussion in other postings <link> about increased current consumption caused...
