Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
To the kind attention of Nordic support team,
I'm working on a nRF52 based product, I saw using your sniffer that after LL_CONNECTION_UPDATE_REQ
I have got a Window Offset...
We have an nRF52 DK and have developed a customer board. On the custom board we have a header with pins for power, ground, clock, and data.
When I connect this to the nRF52...
Hi,
I've got ANCS working well in my application, but I seem unable to increase the length of the notification's message that I receive.
BLE_ANCS_ATTR_DATA_MAX is defined...
Dear sir,
I have an two problem:
1) Once change the device mane, after system rest some junk value is stored Note : here the device name read from the flash memory ...
I'm trying to run Provisioner Example on my nrf52840 DK, which is in examples/provisioner directory, . First I've build softdevice on DK and then I'm trying to build provisioner...
Hey NordicSemi. In my new project, I use DK NRF9160 and I need to determine the location. Since hardware GPS does not work, I decided to use the detection of coordinates through...
Hi,
Something locks-up my I2C sometimes and I need to make I2C recovery. It looks like Nordic has not implemented the zephyr i2c_recover_bus function, so I guess I need...
I'm looking for dual core inter task communication examples
where a thread on one core is interacting with a thread on the other core ?
e.g. will there be some kind of...
Hello All,
I was looking at the Digi XBee3 modules for a ZigBee project I am working on. What is great is they allow you to write MicroPython code to control the network...
I am trying to send some values from nRF52810 Board to my Laptop. I am using a nRF52840 Bluetooth Dongle to connect the board to my laptop. I am using the "Heart Rate Collector...
Is there a way to get the values of CompanyID ProductID & VersionID before provisioning? I'm working on my android application using the nRF Mesh Library and after identification...
Hello, I work on nrf9160 dk and i try to get tx power: For exemple, with a RSRP -76 dbm i get this consommation curve (read current on P24 throught 0.5ohms resistor):
and...
Hello,
we are developing a HID slave device. we need to support five cell phones connect and bond with the device not at the same time.
we use the ble_hid_keyboard example...
