Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hello.
I have a question about setting MAC address.
For now, my device uses random static address from FICR.
And I also use "bt_set_id_addr()" function for test purpose...
Hello
I'm having some issues setting up monitor mode debugging with the nrf connect sdk v1.4.99.
I've roughly followed the steps outlined in this guide , the exact steps...
Hello,
I am trying to program my NRF52840 chip with the Secure Bootloader UART project, in addition to the BLE App UART project as mentioned in the title. So far, having...
I am trying to work with Bme680 with I2C communication i can read every value but i cant read air quality value its always at 806516 value and does not change . I thing configirations...
I've been trying to integrate CLI over USB CDC ACM into my project, but I'm failing even to run the SDK example.
CLI works fine over UART, but it won't run over USB.
...
Hi,
My application has hard faults sometimes, and I'm trying to figure out the reason.
When it occurs - I have a hard fault log, but p_stack->pc is 0. I can't understand...
When I use j-link soft uart all good
but when i disconnect j-link the soft uart will error
like this so�rceid=2, status=0 sourceid=3, status=0 sourceid=4, status=0
Hello,
I'm new to BLE product and nRF52840 dongle and DK are my first BLE evaluation kits. I've some experience in Arduino AVR microcontroller. My setup is as follow:
...
Hi All,
I've been successfully using Martin's example - https://github.com/Martinsbl/nrf5-mpu-examples/tree/master/nrf52-mpu-easydma-using-gpiote-and-registers - for DMA...
I need to connect a PN532 V3 Module to a nRF52840 using SPI. I tested it using arduino IDE (I used those three libraries: Adafruit_PN532.h ( github.com/.../Adafruit_PN532...
We have custom board which is interfaced with PCA10040 board through bebug out port. Blinky example is working fine on 10040 but when I download it on evaluation board its...
Hi,
I've been following below tutorial and everything works fine.
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-characteristics...
The loader script provided to Segger for use with Embedded Studio includes
. = ASSERT (( __tdata_load_end__ <= __storage_flash_start__),
error: section .tdata overlaps...
Hi, I'm working on a project with the nRF52840 PCA10056 board. Using the IoT LwIP MQTT example, I can communicate with the insecure MQTT. However, I need to provide security...
I would like to use the GATT queue to discover ALL primary services. When using the SoftDevice calls directly, one would use sd_ble_gattc_primary_services_discover(conn_hdl...
