Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
I have follow the implementation guide to build the hello_world example and build using the following command
west build -b nrf5340dk_nrf5340_cpuapp samples/hello_world...
I am attempting to run the example program 'heart_rate_collector.py' found in this repo: https://github.com/NordicSemiconductor/pc-ble-driver-py/tree/master/pc_ble_driver_py...
Hi There,
I am using NRF52840 chips in my system. Right now I am designing antenna for the chips. I think the reference SCH of nrf52840 have been completed the match from...
I'm using nRF52 starter kit (nRF52832AA)
I'm trying to build the ANT+ BPWR tx example from Nordic (17.0.2 + 7.0.1)
Having some issues running it, but removing ant part...
Hi,
I am using nrf17.02 sdk and nrf mesh 5.0 sdk for nrf52832 dev kit.
1) I want to send the data to UART not on RTT while using the mesh example "provisioner" example...
Anyone able to run the nRF9160 DK on Window 7? I see the 3 serial ports and the mass storage device but even though I see the device in the Programmer app I get "Unsupported...
Hi dear,
Good Day!!
I am using nRF5SDK1702d674dde\examples\ble_peripheral\ble_app_uart- software to test the UART over the BLE to my mobile , The BLE was automatically...
Hello,
i am using "ble_app_uart" example code in nrf SDK to connect to bluetooth and to read-write the data after connection through nrf connect application.
write...
We are using a custom board with softdevice S132, sdk14, and freertos and ana nrf52832.
Our ble_app does:
init gpio put up a splash screen via a display on spi
...
I am starting a new project using SDK 17.0.2, DK52 dev board and Segger embedded Studio.
To create the new project I started from ble_app_buttonless_dfu and commented out...
I got the update notice for 3.6.1, the install gets to around 33% then just sits there. This happens both with upgrade and with clean install for me, I left it to hang for...
Hi all,
in my current platform I have:
a DK (we are working to implement HW modifications to use a nrf52 dongle for this purpose) that is performing as a Thread DFU...
Hello,
I am currently trying out the assert mechanism of Zephyr.
I have added CONFIG_ASSERT=y to my prj.conf file and included " sys/__assert.h " in my main.c .
My program...
Hi,
May I ask what's the minimum reference circuitry for running nrf52840 without RF? Thanks.
My scenario is as follows.
1) RF, eg, Antenna is not needed
2) GPIOTE...
Hi,
I'm developing a CENTRAL using 52832 to connect a earphone.
1.When I enable LESC, the pair fails with the AUTH_NOT_SUPP error. Why ?
What I think if the earphone...
