Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
I first noticed this when incorrect flags reported by mcumgr when performing network core update
When performing a network core update with CONFIG_SECURE_BOOT_APPCORE enabled...
Hello Nordic community,
using nrf5-sdk for nrf52840 SoC, I followed the uart example as below.
The uart tx and rx works fine BUT NOT THE HWFC
eg. When the CTS is set...
Hi Nordic Team,
Below are the configurations that I have done for the nRF21540 FEM.
.config file
#
# Multiprotocol service layer (MPSL)
#
# CONFIG_MPSL_FEM_ONLY is not...
I have a question regarding the solder balls on the WLCSP package of this device. Are they collapsing or non-collapsing? Can you also provide a definitive source for this...
I have been working on a soil moisture sensor for my indoor plants and I wanted to build some skills in PCB design using a Nordic SoC. I have chosen the nrf54L15 for this...
Hi,
I've got two ESB transceivers talking to each other - a PTX on nRF52832 (E73 module) and a PRX on nRF52810 (Holyiot module, the "tag"). Both chips can obviously TX and...
On a recent run of prototypes using the nRF9151 and the nPM1300 we've had a few failure where the nRF9151 cannot connect to the debugger and the board exhibits much higher...
I have two nRF9151 DK boards, both hardware revision 1.4.0, both showing the same SIM detection failure.
Symptoms on both boards:
AT%XSIM? always returns %XSIM: 0,9...
We have purchased a radio fitted with the nRF9160 modem and fitted it with a roaming SIM for NB-IoT use, we are in UK and have Band 20 EE and Vodafone.
What are the initial...
Now my product need FCC, and I use DTM example, only changed the txd,rxd pin in firmware, the lab can use nrfconnect for desktop to enter test, but the tx power is low when...
Dear Nordic,
I'm designing a 0.6mm thick 6-layer rigid-flex with the nRF54L15-CAAA, and due to my current stack-up the ground polygon to trace clearance can only go as small...
Hi Nordic Team,
Could you please clarify the SDK/NCS compatibility for the nRF54L15-CAAA chip?
We are planning to develop firmware in bare-metal mode and would like to...
Hi For a product, I'd like to have (well it's a requirement) the firmware update encrypted. So I set the following in sysbuild.conf: ... SB_CONFIG_BOOT_ENCRYPTION=y SB_CONFIG_BOOT_ENCRYPTION_ALG_AES_256...
Summary
On a small fleet of identical nRF52832 units running the same firmware (NCS 2.5.1, SoftDevice Controller, BLE peripheral, LFCLK = RC with calibration), individual...
