Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
hi all ,
zephyr bt_hci_core: HCI driver open failed (-5)
i follow this link .(open lte-m(udp) and gps between psm mode on NRF9160)
now ,i need add HCI driver to control...
Hello,
I am working on nRF52832 using SDK 15.3.0 in segger studio.
In my application I am calculate time interval of plus, In which i am given plus to the board pin...
I use:
pca10059, connectivity_4.1.1_usb_with_s140_6.1.1.hex
nrf-ble-driver-4.1.1-win_x86_32
I am trying to scan BLE advertise. I have a problem that ALL packets...
Hello,
I am using Segger and nrf52840 dk. I want to print float value in debug terminal but the value is not getting printed.
I did this-- printf("%f cm\n", temp);
in...
Hi!
I am currently trying to build the lwm2m_client. Currently I am using ncs v1.1.0-rc3.
I am using the devkit as hardware. The only thing I changed in the proj.conf...
Hi Nordic Support Team,
i'm working with nrf52832 development kit. In that, We are adding the UART features in BLE DFU secure bootloader example code in SDKV15.2.0. But...
Hi all,
I have tried to write a program for configuring and send a character data over UART,but the NRF52-DK not responding to the code,I successfully flash the code.
...
I can't seem to get TWI working, attached are main.c sd_config.h
The code compiles, but when stepping through in debug, it ends up in an infinite loop inside:
I have...
Hello,
I am in the process of integrating a project where I need 3 uarts to work concurrently in different configurations. This will eventually migrate to an application...
Sorry ,I have the problem with increasing the max data length(more then 20 bytes) in the characteristic , I change the att_mtu size like the value in the picture, but after...
I have developed a beacon application which transmits the required data from an analog device. I want one more application which scans the transmitted information from the...
Hi,
I am using nRF52840 dongle for my development with "usbd_ble_uart" profile from SDK located in this following path RF5_SDK_15.2.0_9412b96\nRF5_SDK_15.3.0_59ac345\examples...
Hi.
I saw lots of questions but I could't find answer about BLE & flash write func.
Setup is nrf52832, S332, SDK 15.3.0.
using ble, ant+, gpio, timer, adc,
in code...
