hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi guys I m trying to send a simple message every time a gpio interrupt occurs on the client in order to receive that on the server. I m using the ble mesh protocol and I...
Hi
We will use the 52811 together with nRF9160 for short range communications. Currentconsumptionwise which interface is recommended, UARTR, TWI or SPI?
I am trying to run the example secure_bootloader\pca10040_ble_debug. The application does crash during a debug print with following stack trace:
Any idea what could...
I've reached a critical point in the firmware development process where I need to start considering integrating a bootloader with the application code.
I have a custom board...
Hi,
I'm trying to update the modem firmware on my nRF9160. I believe the current firmware is mfw-m1_nrf9160_0.6.8-30.alpha. I followed Martin's suggestions here , but nRF...
Hi,
If i had a purpose of including Ble files into peripheral example then what is the way i can approach?Is it by including all neccessary header file paths,adding sources...
I am working with nRF52832 platform and using some Bluetooth examples like blood pleaser and heart rate. I am wondering how I can count the number of data transferred bytes...
Hi, I try to combine example Blinky with Uart. but i have problem error as link below
Output/blinky_pca10056 Release/Obj/main.o: in function `uart_init':
undefined reference...
Hello,
I am a new user.
I am currently trying to use the 1NCE and Hologram sims, and using LTE Monitor to check the connection.
I am able to see that the signals are...
In our application we use nRF24AP2-USB for some time now.
To test the ANT antenna we use a test program called "USB2_IQC_Test.exe".
This program compares a DUT with two...
I currently have a piece of firmware that uses SDK 15.3.0. The application that have developed that makes extensive use of PPI channel 1 to drive ADC sampling with a timer...
Hello, I'm just starting to experiment bluetooth with the nfr52840 DK board and the sample programs available, especially those "ble peripheral" and as a beginner I started...
Hello,
1) I am using the PCA10040 to program a nrf52811 chip on a custom board with SDK 15.3.0.
2) I'm using the example ble_app_uart_pca10040_s112 on uKeilV5
3) Initially...
Hi I wonder if there are any PPS signal from gps part to the cpu, preferable some kind of timer input or interupt port so it is possible ta make absolute timestamps with fractions...
