Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
For a very small percentage of our devices, we sometimes see watchdog reset events that we cannot explain. The only pattern that we see so far is that the watchdog reset happens...
I am currently developing a project using an nRF5340DK and a custom board.
For some unknown reason, the device is being identified as an "Unknown device." The ironic part...
uart_nrfx_uarte.c, uarte_pm_suspend checks some preconditions with __ASSERT_NO_MSG. In my experience that causes unintended and not required crashes. If the precondition is...
I am building my custom PCB with the nRF52840 chip using the Fanstel BT840F SoC. I have designed and fabricated my own PCB. I am able to flash the code onto the SoC only once...
Hello,
While using ai.lab.nordicsemi.com for model training, I noticed that after the training process is completed, the platform generates several performance charts, such...
Hi,
In my board design, I'm planning to use nPM1300 to power nRF5340 and nRF7002; the user has the option to connect or not connect a battery. If I programme the current...
Hi,
We're developing BLE products with the software developed on nRF SDK v3.2.2.
We are affected by the known issue of the SDK: NCSDK-32763: Upgrading firmware may corrupt...
nrf 5sdk + s140 + 52833 I'm currently debugging the time-sharing operation feature for BLE and the private protocol. I've found that after I power on and initialize the SoftDevice...
Hello,
We currently have various products built around the nRF52810 and the nRF52832. We almost always use a PCB antenna very similar to the one on the "nRF52840 Dongle...
Hi, I am working on project to obtain ecg data via bluetooth. But before that I was trying to see whether I could obtain ECG signals serially through nrf52833. And I tried...
Using nrf5340 with nrf70 on a custom board.
I want to use the wifi interface to send raw wifi network packets (both in associated and non-associated modes).
I have the...
Hello Team,
As we have purchased nRF9151 DK from you, we are not able to import the exact SDK required to develop using nRF9151 DK.
Kindly please let us know how we can...
Keil SDK13 BLE OTA upgrade failure causes the device to become unbootable, requiring re-flashing. How can this be resolved? We are using the bootloader_secure_ble bootloader...
