I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
I want to use the CUSTOMER[] fields for their apparent intended purpose of storing calibration data in nonvolatile memory. I find it quite absurd that the softdevice would...
Hi,
I am using PWM to control LED power.
The code i use for initializing the PWM is-
app_pwm_config_t pwm1_cfg = APP_PWM_DEFAULT_CONFIG_2CH(1000L, PIN1, PIN2); err_code...
Hello,
I am trying to run the example DFU over TFTP. I have setup a tftp server with following configurations:
# /etc/default/tftpd-hpa TFTP_USERNAME="tftp" TFTP_DIRECTORY...
Hi,
I've followed the link https://devzone.nordicsemi.com/f/nordic-q-a/35675/how-to-use-static-passkey-for-a-no-display-no-output-peripheral
and added it to uart example...
Hi,
My app requests a timeslot in various conditions - sometimes the timeslot needed is long, sometimes short (unknown a priory) so it asks for the longest possible...
Hi,
Is there any easier way when using Eclipse IDE with GCC for nRF5 SDK 15.2 development to get the Include files in the examples to be recognized easier than tediously...
My set up contains beagle bone black as Application board. PCA10001 board with S120 Softdevice using nordic_sdk_10 running ble_connectivity example program.
I initiated...
I have a Teledyne protocol analyzer for capturing over the air data between an nRF52840-DK and an iPhone 8 device. How do I obtain the encryption key from the nRF52840 SoC...
Hi,
I want to verify Bluetooth on my board is good or bad.
Note that, I do not have any spectrum analyzer or vector network analyzer, just development kit.
I found example...
On the product page the nRF52810 is mentioned as supporting ANT. https://www.nordicsemi.com/eng/Products/nRF52810
However in the info-center looking at the compatibility...
Apologies if this is a Segger question vs a Nordic question.
I have already been evaluating SES for a non-Nordic project, and so it's already installed [on Mac].
I am...
Hello Nordic,
I have already used an earlier version of nrfconnect on this lcomputer( windows 10 language PT-BR).
After upgrading to 2.6.1 I got the the error below: ...
Zboss som times gets stuck in loop trying to start network steering when running sample, most of the time it eventually makes it out of the loop
but what causes the failure...
Hi,
I am using nrf51822 to get DS18B20's temperature data, but I am fail to do it.
Would you please give me an sample C source code which can get temperature data from...
in nRF5_SDK_14.2.0_17b948a project, we get sensor x y z w data in a loop process, the data which print in uart shows very smoothly.
but if i push buttons many times in a...
