Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hello all, i am working on nrf52832 ble board. right now i try to add secure pairing connection for security purpose in my code. i use segger studio for programming. i did...
Hi, We made a custom board using the NRF52832. Everything is working in our system except BLE part. We are using SDK 13 with Softdevice of S132 v4.0.2. We tried to flash examples...
I'm using SDK 14.2, S132, and the NRF52832
This problem occurs during the pm_init() function when initializing the soft device. Investigating further has led to the pages_init...
Hi, I've been tasked with sending commands to an nRF52840 Board via a React Native mobile application I've developed, but have no idea how to do so. Our company uses:
...
Hi all,
I would like to learn how to use the USB peripheral these days. So, I programmed the example of usbd_cdc_acm on PCA10056. The PCA10056 couldn't be identified after...
nRF5 SDK structure project use makefile and sdk_config.h header file, When I want to add a component to my project. There is too hard work to modify the makefile and sdk_config...
Hi everyone,
I am trying to understand this sample code: here
But I don't understand how to choose an arbitrary pin for the LED.
And also, in LED_MASK which pin is...
Hi,
I recently dug into the potentials of the NB-IOT network allowing iot devices to directly make use of cellular communication. With the release of the new nrf9160 containing...
Hi,
Recently, I was trying to pair the nRF51822 development board by windows swift pairing.
While I turn on the swift pairing function, I still cannot use this feature...
I have a similar question to https://devzone.nordicsemi.com/f/nordic-q-a/32115/how-to-parse-the-log-file-of-the-nrf-connect-for-desktop
There are lots of data in these log...
Hello.
Recently, our supplier recommend us to use nRF52810 instead of nRF52832.
These two MCU have same pin map, so just we pulled off existing nRF52832 from the board...
Hi,
we had used nRF52810 in our product. Our product is undergoing FCC & IC certification.
FCC & IC regulatory body had requested to provide Tune UP tolerance values of...
Hi There,
I was trying to understand the step to create a test app for dfu bootloader update via BLE for PCA10040. Below is the documentation I read.
http://infocenter...
Good day
My nRF51822 uses the Eddystone example with SDK 12.3.0 in conjunction with S130. When I configure TLM in slot 1, I notice that the temperature is about 6.5 degrees...
