Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using the light switch example with the mesh SDK version 3.10
the provisioning is done with NRF Mesh application (android phone)
1. is there easy way to get...
The table under 5.4.4.3 in the datasheet for the nRF52840 lists the shunt capacitance for the LFXO as 2pF max
C0_LFXO (Shunt capacitance) 2pF max
What is the risk if the...
Well - Where shall I begin? The more I look around on the web the more confused I get.
I need to create a Connection betwen a PC running Windows 10 and a sensor device server...
Hi,
I have setup TWI peripheral for async transfers via IRQ and callback. After firing the transfer operation, I feel uneasy about having no control until the interrupt...
Hi
I need to certify a product in FCC and they sent us what they want. Radio_test_example is basically what I need, but the problem is that I'm using SoftDevice 110 and...
I was working with the buttonless DFU service that requires bonds and I was able to update my firmware just fine. Then I added Just Works OOB pairing using the nfc_ble_pair_lib...
Hello,
I am in big problem, just couple of months ago i managed to run dfu over BLE mesh. Even now its working in windows platform but for some strange reason its not working...
Hi,
I use dongles with custom application that combines Thread and CDC ACM. The application works fine, but after restarting PC several dongles with this application stopped...
Hi,
I have a smartwatch that has a nrf52832 chip inside. It firmware runs on S132 SoftDevice ver 2.0.1 and has an OTA bootloader which supposingly allows me to upload firmware...
I am evaluating the nRF5284 SDK 15 Module in HCI mode. I am trying to scan Extended advertise when: 1.Extended non connectable non scannable advertising, Primary_Advertising_PHY...
Hi,
I have just purchased a nRF52840 usb dongle ( https://www.mouser.in/ProductDetail/Nordic-Semiconductor/nRF52840-Dongle?qs=gTYE2QTfZfTbdrOaMHWEZg==) .
I would like...
Hello, I am a beginner and I just got a Raytac "MDBT50Q" bluetooth 5 module based of nRF52840 Soc.MDBT50Q does not come with a builtin frimware to respond to AT-commands.Can...
Hello, i have this problem with DFU, in Mesh SDK v3.0, i am using PCA10040.
this is my boodloader_config_default.json
and i am using this for make the pkg.
and...
Hi!
For our development purposes I am implementing NRFUTIL 0.3 for mesh on Android/Java, migrating it from Python code, via UART/Serial, for DFU purposes
It looks like...
Hello,
I am having difficulty using a single TWI to support a DAC (MCP4725) and IMU (BNO055).
I am using nRF52 DK, and SDK 14.3 with the SEGGER IDE. The DAC is running...
