Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I have a demo(s110) set up with some custom services, and in them custom characteristics. The services each relate to a specific sensor element on my device, so have a mostly...
I'm using ble_nus_string_send() to send 15 bytes over BLE UART.
As expected it sends 15 bytes, however on occasion 14 bytes are sent instead of 15 bytes.
Would there...
I ordered nrf8002 IC. I am using following breakout board PCB & not using Nordic development kit.
www.proto-advantage.com/.../product_info.php
I gave 3.3V to both VDD...
I've been working through the tutorials on BLE Services & Characteristics. That's all gone fine for me. Now I'm adjusting the sample code to use different UUIDs for my own...
Dear Sir.
I have a question for app timer in nRF52 DK(pca10040).
I was called a example source(ble_app_hts) for nRF5_SDK_11.0.0-2.alpha.
And I add UART part for logview...
Dear All,
I have question regarding advertising in NRF51. I measured the power that be used when advertising using osciloscope and set the advertising interval of NRF51...
I'm having this event and I'm not sure what are the conditions required to trigger it, also what does it mean exactly since the documentation does not say more than a line...
I had attended the Nordic 2015 Tech tour in Helsinki and it was very nice of Nordic to give away nRF52 DK to all attendees. So far, I've been busy working with nrf51 but today...
I follow this instruction to turn Raspberry Pi into an IPV6 router on IPV4. My raspberry pi works well after I add nameserver to /etc/resolv.conf.
But other device in my...
I am experiencing an error that I can't figure it out why it is happening and where to go and try to fix it.
I am using the subscriber implementation on my nRF51, Raspberry...
I see in multiple examples of NRF51 SDK:
#define APP_TIMER_MAX_TIMERS (2+BSP_APP_TIMERS_NUMBER) /**< Maximum number of timers used by the application. */
but it is...
In ble_gatts.h, I see:
#define BLE_GATTS_FIX_ATTR_LEN_MAX (510) //< Maximum length for fixed length Attribute Values.
#define BLE_GATTS_VAR_ATTR_LEN_MAX (512) //< Maximum...
Hello Everyone,
I have been working on the NRF51DK by using proxmity examples as reference when i added the static passkey for the connection security it is working well...
Hi, i am new to embedded system.I want to use nrf52 DK as master and connected with two slaves by two spi channels? is it possible to achieve on nrf52 DK.
1>How to set up...
