Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I have a custom hardware, with an external 128MB QSPI flash memory connected to a nRF5340. My current task at hand, is to store firmware update images for MCUBoot...
If I am having a custom board created and assembled using a pcb maker (makerpcb, jlcpcb, or pcbway) what do I need to ensure is on the board so I can flash and debug it? I...
We have a issue about nRF9161 on our custom board.
we flash hex our board. It doesn't work very well. sometimess it work and consume about 90mA current. sometimes board...
In our project we use a SHT4x sensor connected to I2C bus of nRF5340. To lower power consumption during idle/sleep we've a power line switch to disconnect the SHT4x from the...
Hi Nordic team,
I was testing whether Zephyr's LLEXT would work on the nRF52840DK. The example can be compiled on NCS 2.7.0 and loads fine. However the final step of having...
I am working w/ the nRF5340DK, and the project mentioned here (NCS v2.5.0, nrf/samples/crypto/rng). I was able to build/flash the project.
I wanted to verify whether the...
Hi,
I am getting to grips with the device tree and when i add an over lay file to the project, the 'new' devices are flagged with the waring that theyre being over ridden...
Hi,
using nrfutil pkg to generate the settings.hex file for the DFU is exceptionally slow on my M2.
I'm using what I believe is the latest version
nrfutil 7.5.0 (063f665...
I have an i.MX8 arm linux system running an OS based on yocto, with an nrf52840 connected over USB. The linux system receives nrf52840 firmware as part of its OTA, and updates...
Hi there,
Currently, I'm working on a solution where I need to design a software UART through emulated GPIO pins for nrf52833.
The requirements are that, solution would...
Hi all.
hello everyone . I have a project on the nrf52840 board . The wiring of the board is shown below . The module is correctly flashed , but does not start . As if it...
Dear Support,
I was working on refactoring the project and changed a majority of cmake files to improve the architecture of the project but when I finished I found out that...
Hello. "zephyr/samples/drivers/adc/adc_dt" example sample added an additional adcpin.
When reading the sensor value connected to AIN0, the value of AIN1 is also changing...
When I used the code to get the RSSI values for different channels, I found that it was very time-consuming, about 400-500ms, and most of the time was spent waiting (NRF_RADIO...
Hi.
Please tell me if it is possible to realize such a connection scheme?
I want the Dongle to act as an intermediary for data transfer from the custom board to the smartphone...
