Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi,
is it possible to write data to external spi flash using nrfjprog? This would be on a custom board, which has nRF9160 with extra external SPI flash (not QSPI)?
...
Hi,
There is a bug in ncs\v2.7.99-cs2\nrf\cmake\version_app.cmake
add_custom_command( OUTPUT ${PROJECT_BINARY_DIR}/include/generated/app_commit.h COMMAND ${CMAKE_COMMAND...
I am using nRF Connect fro Desktop Bluetooth Low Energy Standalone v4.0.4 with a Dongle USB nRF52840.
I can see my device when Legacy Advertising is enabled, but if I only...
Hi,
First of all, let me confess, I am new to VS Code - NRF SDK environment.
I have a VS Code setup with NRF extensions enabled and due to some reason, the error squiggles...
Hi , I 'm trying to send and receive on a websocket. Sending works fine and is received on the backend, but when I try to receive I just get garbage in my buffer.
I sanity...
Hi,
I'm currently trying to add MCUBoot in my project.
The project was built successfully by adding these lines to prj.conf.
CONFIG_BOOTLOADER_MCUBOOT=y
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
I'm looking into using command line builds for nRF Connect SDK again due to issues I've been running into with vscode.
The instructions on this page ( https://docs.nordicsemi...
I have tried zephyr/sample/bluetooth/periodic_sync_conn in nrfsdk v2.7 and test on nrf5340 audio dk, and doens't work. the output is:
*** Using Zephyr OS v3.6.99-100befc70c74...
Hi,
How to solve the problem of writing data to flash using the write_data_flash function in save_stack_data function
1.1. I tried to add the function save_stack_data...
Hi! Background (feel free to skip) --------------------------------------- We have 3 nRF52840 boards, connected via ble/NUS as follows:
B also advertises bluetooth HID...
Hi, we are using the nRF9160 in conjunction with the nPM1300. To power off the device, we call lte_lc_power_off() which sends the AT+CFUN=0 command to the modem and waits...
the v2.7.0-5cb85570ca43 zephyr/ndk combination doesn’t work for things using the JSON_TOK_FLOAT type (vs the number type). this is because zephyr/lib/utils/json.c:float_ascii_encode...
I am working on a project in which i have got 100 nodes we are doing it in our custom board. so i need to assign unicast address manaully for each nodes inside it. How can...
When I try to build any application with west I always get a CMake error complaining that it is unable to run the Python version included with the NCS toolchain. The error...
