Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Do the LED drivers on nPM1300 have any ability to control either current or do PWM dimming? led_set_brightness() seems to not do anything and from the datasheet its not quite...
We have an nRF52833-based board, software is based on Zephyr and Nordic SDK 2.1.2. One of the SPI interfaces connected to external flash (Winbond W25Q80DVSNIG) Board is battery...
I have successfully implemented an interrupt-driven method to read data from the MPU6050 sensor on the NRF52840, and it functions as expected. However, I encounter an issue...
Hi Nordic team,
The LTE link monitor app is not showing up in my NRF connect for desktop v3.6.
What would I need to do in order to add it?
Is there a http link you...
I have written the code to test the RSSI signal, and the segger shows the result on the debug terminal, However, the debug terminal can only show first 500 data, the first...
Hi,
I have installed NCS 2.7.0 using the nrf command line tools, and followed the tutorial to install the NCS VSCode extension in VsCode. However, when I compile the Matter...
After I flash my code,I get imformations as follow:
*** Booting nRF Connect SDK v3.5.99-ncs1 *** ***引导nRF Connect SDK v3.5.99-ncs1 *** ***引导nRF Connect SDK v3.5.99-ncs1...
Dear Sirs!
I used SDK 12.2. Product was developed some years ago and now I am working for upgrade. One of new features is UART. I faced very strange problem.
I send...
Hello,
I am developing a HID device with DFU OTA and would like my customers to be able to upgrade this product independently via DFU OTA in the future. I would like to...
Hello Everyone,
I would like to interface the Accelerometer to nrf52810 via TWI pin P0.06 as SCL and pin P0.09 as SDA. I have to read the accelerometer data and send over...
Hi Nordic I am transmitting the dmic stream from nRF5340 dk to nRF5340 Audio dk. But I am not hearing the nRF5340 Audio Dk. Getting below Wrn's How can I hear the audio on...
Dear expert.
one of my clients manufactures medical devices.
as you may know, medical devices need to special certification depending on the country, such as North America...
Hoping someone can point me towards some guidance on how to properly enable, configure, and build mbedTLS options on the nrf52840.
I'm currently using Zephyr 3.6, with the...
Hi,
I developing an Hearing aid accessory with nrf5340 audio and STM32.
I do not have external flash so I need to use the nrf5340 internal flash.
I'm using the 2.5.0...
