hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello, I have a question about how to monitor Zigbee devices for dead or alive, especially end devices that sleep. I am currently developing a hub to control and retrieve...
Hi,
I am working on a project with an nrf9160 on a custom board that I first developed with NCS v2.6.1.
I am trying to upgrade to latest NCS v2.9.1 but I am facing an...
Hello,
I'm using nRF54L15DK and nRF Connect SDK 2.9.0. I'm running a BLE peripheral code and try to pair with my iPhone using nRF Connect mobile app. After I hit "connect...
Hi, I'm working with the nRF9151DK and Zephyr RTOS (v3.7.99 / NCS 2.9.1) . I’ve configured UART1 to send and receive data via GPIO pins:
TX: pin 8 (P0.08)
RX:...
Hello,
I am setting up a board configuration for my custom board and trying to get a bluetooth sample (heart rate profile) to compile using the board configuration.
...
Hi!
What is the max PDM frequency I can set? Is the clock limited to these options?
https://docs.nordicsemi.com/bundle/ps_nrf5340/page/pdm.html
https://www.infineon...
I have a project where we did not populate the external oscillator for our custom board which has an nrf5340 on it. I did most of my BLE testing on the nrf5340 devkit and...
Hello,
I have a question regarding the internal handling of the update recovery process for BLE mesh DFU, specifically within the DFU Server model + BLOB Server model. ...
I am a beginner in BLE systems. I am designing a board with a Nordic chip, and I have difficulties in designing an antenna... Can you look at my technical solution and correct...
Hello,
We are using Raspberry Pi + NRF52840 as Borderrouter for Openthread using Radio Coprocessor design.
However we are facing stability issues on the RCP where it...
Hi everyone,
After a debugging session using the debug tool in nRF Connect SDK with an nRF52832 on a custom board, the chip is now completely unresponsive—I can't flash...
Hello,
I am conducting a feasibility study on implementing Auracast capabilities using the nRF5340 Audio DK with nRF Connect SDK v2.9.0. My goal is to investigate the potential...
Hello,
I have an application that I built for the nRF52832 using the peripheral uart example that uses Bluetooth. I am using NCS 2.7.0 I am using the following peripherals...
This issue is a follow-up to the previous one： 341132
When upgrading our device from Matter 1.1 to Matter 1.3 firmware via OTA, the MCUBoot program in the old firmware fails...
Hi, We are trying to provide example support for our RAK4631 (nRF52840 based) and an ultrasonic PDM microphone (RAK18032). We have been able to get a sample frequency of 100...
