Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
Hi,
We are having trouble configuring our PDM peripheral to operate at 48 kHz. THe nRF5340-specific documentation on the PDM module has equations suggesting that 48 kHZ...
Hi Folks, I’m working with an I2C LCD rated for up to 50KHz and it is showing a fair number of glitches. Can anyone tell me how to lower the I2C speed from the default values...
I'm writing a custom bootloader for an nRF52840 using the nRF5 SDK v15.0.0. This bootloader uses the SoftDevice to receive BLE packets containing binary data for the DFU....
Hello,
I am evaluating the nRF9161 and nRF9151 and have a few questions.
1. In regard to modem FOTA delta firmware updates, where is the delta file stored in both Serial...
My SPIM seems to stopped working when migrating from NCS 2.5.0 to 2.7.0, so I decided to downgrade to 2.6.0, and it seems the issue is still there. When migrating to 2.6.0...
I have asked this before, but I will ask again.
I have a few questions about the sample source of nRF5340 Audio.
1. Where does the connection process between the gateway...
Hello,
the BSI (German Federal Office for Information Security) released a document February this year which contains a list for recommended cipher suites and TLS versions...
hi ,I am using nrf52840dk- nrf52840 board to interface the IMU Sensor using I2C using nrf connect sdk for vs code. But I am facing error:
i'm using the code in ncs/samples...
Hello im using basic usb over console exaple on my custom board . i believe this task wont require any pins to be configured as my custom board is routed properly to all 4...
Hello,
with the help of this documentation ( https://docs.nrfcloud.com/Devices/MessagesAndAlerts/SetupMessageBridge.html ) i have been able to create a bridge to transfert...
I am trying to test a nRF5340 with a 1.3 inch waveshare 240x240 display using a st7789 driver. How would I connect the display to the board:
VCC
3.3v
...
sdk-nrf: v2.7.0
When PAWR is enabled I no longer get connection timeouts as a callback to bt_conn_cb.connected with the conn_err parameter set when attempting to open...
On the nRF51, LO leakage was measured when in receive mode. For 2402~2480mhz, LO leakage was measured at approximately 2745~2836mhz. The nRF52 does not measure LO leakage...
Hi,
I am using nrf52832 board and I want to configure the SPI0 and SPI1 for the sensors LIS2DW and BMP388 respectively.
I am new to nRF Connect SDK for VS code, I am exploring...
