why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
i used nrf52832 and sdk 14_02 i run this example secure bootloader located in example>dfu folder is get error
return NRF_ERROR_INTERNAL;
on nrf_bootloader_init() this...
Hello, Guys.
I just wondered why max UART exchange when we receive mqtt buffer that is let's say 1707 bytes is splited bu uart in chunks max of 120 bytes.
Is there some...
when i flash bootloader hex file
1) """sd_s132_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds.hex """
NORDIC_BUTTONLESS show but when i try...
Hi,
I have create a separate .hex file for boot-loader & application. when i try to load them into the nRF52382 through "nRF connect".
It says overwriting has occurred...
In the "ble_app_uart" in the ble_peripheral showing the error?
error is -
Building ‘ble_app_uart_pca10040_s132’ from solution ‘ble_app_uart_pca10040_s132’ in configuration...
I've used the PPK2 for a while now, but as of today it started crashing whenever I re-start a current measurement. Both in Source / Ampere meter mode.
The logging says:...
hello Nordic
i am working with nrf52832, with ncs 1.7.1
i am writing my own driver which will be used by 2 baords
one board have to raise 2 gpios to get power and...
I'm trying to read the CTS characteristic from a BLE server (an iOS device) and part of the requirement from Apple is that the server and client be paired and bonded before...
Hi Friends,
- kit dev NF52840-DK
- IDE : segger studio IDE
- SDK nRF52 16.0.0
I want to port the nfc_writable_ndef_msg NFC example to freeRTOS.
I use the NFC Tools...
I'm learning that there are issues with the early "engineering versions" of the nRF52840, identified with QIAAAA marking.
Apparently the SPI3 BUS is not fully supported...
Hi,
After some strange behaviour of the DAC4716 chip, I want to try and reset it. The datasheet describes a way to do so over i2c using a specific bit stream. How can this...
I am having a N20 Micro Gear Motor with Encoder, I want to read data of c1 and c2 using GPIO pins. Any specificAPI, method or suggestion for this?
I am using nRF5340 along...
We have an application running on an nRF9160 development board (shortly to be ported to a production board), which listens on a serial link for sensor data, which is then...
Hello,
For network testing, I would like to use the Modem Shell App sample with the Thingy:91.
As suggested in the overlay file, I can disable some features, so the Build...
