Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
Hello.
We are developing using nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral device.
I have a question about setting the UUID. My program has one advertised UUID...
I am using slightly modified master SPI example from here which is running on nRF5340 to communicate with slave device, which is RHD2216 . SPI frequency is NRF_SPIM_FREQ_4M...
Using a nRF52832, I would like to broadcast advertisement packets normally and in extended mode at the same time. Is this possible or do I have to ping-pong between, stop...
ok,i recenlty have gotten iq samples from Rx.but i think my received iq samples are from Tx .i use the NCS 1.9.1 with two boards nrf52833dk.
firstly,i connect antenna array...
Hi, I have already updated all certificates and firmware. But when I am trying to connect my device to the cloud it does not recognize my device. when I am trying to add my...
Hello Dear,
Why the time of uplink state is 950 ms if the data packet size is 0 Byte in mode NB-IoT not in LTE-M?
Can we say that every time a data is sent, it takes 950...
Hello, All
I received following message when I test the code, it appears on both sides,
ASSERTION FAIL [chunk_used(h, c)] @ WEST_TOPDIR/zephyr/lib/os/heap.c :163
unexpected...
Hi,
I have installed Segger Studio for ARM v6.22a.
I have also installed the SDK5 version 12.3.0.
I imported the IAR project project ble_app_start_notification_pca10028_s130...
Hi,
I am after some assistance with creating a 6 layer stackup to use with the NRF52840_CIAA that is 1.6mm thick.
Can you provide recommend layer stack up that have been...
Hello.
Is there any difference between i2s hardware in nRF52840 and nRF52833? I made WS2812B i2s driver and working very good on nRF52840. The same code (project is adjusted...
Hi, I'm developing an application which is merging from (ble_app_uart + libuarte + app_timer + pwm). Here is my main.c Now I'm developing an feature that using timer ((app_timer...
Hi,
As mentioned in subject line, I am trying to enable BLE SC peripheral in SDK 17.0.1 with softdevice S113. I have enabled the PM_LESC_ENABLED macro in sdk_config and...
Hi Nordic,
My customer has imploy nRF52832 to develop a heart rate equipment.
We have test the ble_app_hrs_c and ble_app_hrs on two nRF52 DK.
I found that if I comment...
Hello Dear,
Why the time of uplink state is 950 ms if the data packet size is 0 Byte?
Can we say that every time a data is sent, it takes 950 ms to get the transmission...
