Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
Hi @Torbjorn!
Hope you are doing good!
I tried using nrf52840/nrf52833 ble_app_blinky_c and ble_app_blinky for connectable coded PHY . But it only works for 1M_Phy . Although...
Hi there,
Our current understanding is that when building an application using NCS, the images of of MCUBoot and the application gets merged into merged.hex.
We however...
I'm a relative novice to linker files, just enough to be dangerous, but I have a need to understand what the Segger linker is doing. I have some success using `flash_placement...
Hi
We are trying to connect to connect to a MINEW MS88SF23 SoC from our nRF52833 DK.
For all tests, nRF power source switch is set to VDD, nRF ONLY switch is set to DEFAULT...
I was trying to reflash UICR for the first time on an nrf52840_dongle using nrfjprog. Here is what I tried:
$ nrfjprog --eraseuicr --program /tmp/new-uicr.hex ERROR: Two...
Hi,
I am trying to measure power consumption on a nrf52840-DK dev board running custom firmware.
I am using PPK-2 and nRF Connect Power Profiler app v3.1.2 for the power...
When RTT viewer is not connected, the buffer will eventually overflow and it causes device hanging and being reset by wdt eventually. When I connect to the RTT viewer before...
Dear Nordic engineers
I made some modifications to the keyboard examples in the SDK based on the NRF5 17.0.2 version. I changed to use a static password for pairing and...
Send a semaphore every 20ms through the timer. After receiving the semaphore in the thread, push the data to the message queue
Then, the message queue is obtained through...
Hi
I'm working on adding software flow control in coprocessor code，
1.CONFIG_UART_ASYNC_API and UARTE_INTERRUPT_DRIVEN ，What's the difference between the two macro definitions...
Hi everyone,
I have the following issue. I have migrated a code for a Bluetooth Mesh network gateway which I developed a few years ago with version 2.1.0 I guess to the...
Hi Nordic,
I am trying to implement a custom uart driver in my inter processor communication application. In the driver implementation I want to use uart with dma and I...
We are porting to the nrf52832 an application that needs to sample the SAADC continuously at 200Khz (alternating between two inputs) with dual buffering DMA of let's say 1k...
Hello Devzone Community,
I am developing an nRF9160 based firmware for a battery powered device, and am attempting to examine the firmware using `gdb` at the command line...
I'm developing two products that will communicate via ble_uart. Both products have battery, so I need to reduce consumption as much as possible. I'm currently using nrf52832...
