Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
Hi iam using nrf52840 dk board and for programming i use keil software ,the issue is i could not program the dk board and it is a brand new board. When I try to program it...
Hi guys! I'm a beginner of nRF52832, and I met an issue as the topic said.
When I init the UART module, it will cause an "APP_UART_COMMUNICATION_ERROR", and the error code...
Note: this question was previously a reply on my other question, but I accidentally marked it as an answer so the thread got locked. I have now deleted that reply and am posting...
Dear All,
could you explain the function of TP8 and TP9 of the nRF9160 DK on HW 1.0.0 ? These test points are connected to pin 124 and 125 of the nRF9160 which are marked...
I am using nrf9160 custom board with an external flash memory mx25l6433f. I first tested the external flash with the example 'sdk-zephyr/samples/drivers/spi_flash_at45' and...
Hi,
I;m working on nrf52840 dk i have to enable ble5.0 long range.
i set the tx power 8.
according to my project my device will be always in advertising mode and my...
I am trying to scan for BLE devices in my area, but when I connect to the USB840XZ with the windows development tool the "Start Scan" button is not active. There are some...
Hi everyone,
is there a way to update the AWS certificates from certificates.h with the SDK 1.9.99? Following the AWS FOTA instructions it seems that i can update the certificates...
Hello everyone,
I am currently testing the secure bootloader over USB example but I am currently facing an issue when I start a DFU.
Here is my configuration:
...
Hi,
Application details:
I have a datalogger application that samples data every second. It uses the following modules:
TWIM0 -> To communicate with external RTC clock...
Hello,
I am working on application using nrf52810 SDK version nRF5_SDK_14.2.0_17b948a.
Here my application sends 240 bytes of data every 150 ms. But after sending few...
Hi,
I use the a gpiote_in_event to trigger a number of PWM pulses which works fine so far. However, the exact behaviour of the generated signal is important so that the...
Hello, I am using nRF52-DK with Segger Embedded Studio and I'm running the following code that first blinks the LED1 on&off 5 times, and sets up BUTTON1 for wake up, and then...
Hi,
I would like to read the temperature of the nRF.
I tried to use the routine I found here in the forum
Sometimes works sometimes the system crash. I notice the...
