Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hi,
I want to use the bsp button to our project, so I tested on the example "ble_app_blinky",
I modified the app button to bsp button, add two custom events to the bsp_event_t...
Hi Devzone,
I've been trying to verify and validate the performance of Instaburst mesh packets against regular ones. I modified a build of the mesh light switch example...
Hello,
I have been trying to get the thingy:91 up for 3 weeks or more now from Sri Lanka. I have made a lot of progress in getting data connectivity via MQTT to thethings...
`Hi There,
For nRF52840 board, If I want to fully disable JTAG or SWD lines after flashing, then what are the options to achieve it.
Questions:
1) If I want to disable...
My use case: There are different but similar peripherals advertising with 1M uncoded or coded PHY. Some of them are even advertising in mixed mode.
Question: How to connect...
Hello all,
I hope you are well. I am currently developing a product on the nrf52810 platform. I have a custom board and now have the BLE functional on the board. The next...
Good Day.
I want to measure the approximate voltage level on the battery in the nrf52820 microcontroller using a comparator (COMP) operating in Single-ended mode. I use...
am following the introductory videos and have done a fresh install of the Toolchain, Segger, VS Connect 3.7.2, nRF Connect SDK v1.8.0 and VS code on macOS
1. Installation...
Hi team,
I'm currently playing around with the sensor server example where I wanted to include the generic_onoff model in a separate element. I wanted to learn how to add...
Sure, my question is very stupid, but after one day I found nothing to explain the principle of the situation, I decided to ask.
I have a laptop with built-in Bluetooth...
Hi all,
I am trying to interface IS25LQ040B serial flash(512KB) IC with nrf52833 (bl653_dvk).
programmed sample code from "zephyr\samples\drivers\spi_flash"
I am getting...
Hi all, im asking question about triggering my own antenna. there's few questions about it. 1. im using TI boostxl antenna array (3 antenna) , periodic table are as follow...
Hi,
I want to use the 64MHz crystal oscillator (HFXO) as the source for HFCLK clock controller. How can I need to enable or disable the item in KConfig on nRF Connect SDK...
Is there a current example for nRF52840 power management under Zephyr / nRF Connect SDK?
Searches for this turn up old examples, such as this one , that are no longer in...
