Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
Our project team has decided not to using an external MCU to interface with the 9160 over the UART. So we'll need to write our application on nrf9160. The application...
P19 (Debug OUT Connector) on the nRF52840 BLE RF Development Board, PCA10056 (Dev Board) provides the ability to program a nRF52840 BLE board (BLE Board).
Questions:
...
Hi there,
Attempting to use the sample program for direction finding and have been following Case ID: 280319. Have attempted to add the code suggested by Simonr in adding...
Hi,
I'm working on a project using Zephyr and ncs 1.7.1. One of its functions is to stream WAV files from a SD card. It only ever reads data.
The issue I'm having is...
Hi all,
I am using SES in Win10. After I updated my NCS to 1.7.1, I failed to open my solution. However, it runs succussfully in SDK 1.6.1. The infomation is below:
...
Hello.
I am currently working on implementing a PWM control function using nrf52840. I used the function "es_battery_voltage_get()" to read the battery voltage before and...
I have written simple hello world code on nRF9160 custom board and enables the MCUBoot as bootloader using CONFIG_BOOTLOADER_MCUBOOT=y in prj.conf file.
Also, made some...
Hi everyone, I'm trying to communicate with OBDII through NUS using nRF52832. I was able to initiate the connection, send commands to OBDII, and get responses on the ECUsim...
The current RRC Inactivity Timer from my provider is 10 seconds, causing my power consumption in RRC Connected mode to be unnecessarily high.
I want to use the Release Assistance...
Hi,
Can anyone check if my understanding about this NFC-BLE pairing feature is correct?
1.Before connecting, two BLE devices will exchange some keys or info for secure...
Hello,
I'm working on an application that will use the nrf9160/nrf52. I will need to make https REST calls where I will populate the http header with username/password credentials...
I didn't manage to find a solution to my problem here but I fixed it myself so I'm posting it just in case it helps someone else.
I installed JLink 5.12.6 and nRF5x Command...
Hi,
Android shows a message that the NFC Pairing was not successful, but it looks that the connection was established successfully (Device in the connected devices, data...
Hi All,
I have a measuring device that needs to send UART data over BLE to a PC with BLE dongle or Macbook with built in BLE. My test users need to open up a webpage in...
