Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
To the kind attention of Nordic support team,
I'm using sdk16 and usbd. Sometime I get
app_usbd_core.c -> usb_core_ep0_handler_check --> NRF_LOG_WARNING("Previous setup...
Hi All,
Now i'm using peripheral - blinky project,and i saw the Block allocator module in the sdk_config.h.
Can anyone tell me what is the Block allocator module use for...
Hi,
I met some problems when I tried the sample 'direction_finding_connectionless_rx' in ncs v1.7.1 on nRF5340dk. I copied files to hci_rpmsg/boards as https://developer...
Hi all,
I got my nrf5340PDK working with the Thread CLI Sample.
I can now connect to the UART interface and issue ot commands.
According to the tutorial Thread: CLI...
In response to a BLE_GAP_EVT_DATA_LENGTH_UPDATE_REQUEST, we have called sd_ble_gap_data_length_update, with the following parameters:
Rx Octets: 251/ Tx Octets: 251
Rx...
Hello everyone, i need to increment a counter each time my button on the nrf534DK is pressed i'm using sdk v 1.7.1 . is there a simple way to do it or a function which supports...
Hello!
I've seen similar posts about this issue: https://devzone.nordicsemi.com/f/nordic-q-a/57105/nrf9160-modem-stuck-in-searching https://devzone.nordicsemi.com/f/nordic...
I am looking to handle low priority interrupts on a single GPIOTE Port Event but when attempting to add the second pin with the same handler i get an error and the handler...
Hi Team Nordic and fellow engineers, I am seeking to find better parts from Nordic RF Transciever lineup
to replace nRF24L01P-R, in order to improve the performance of the...
Hello, I intend to use libuarte under FreeRTOS together with the SoftDevice (SDK 17.1.0). An app_timer is used for the RX timeout. I think there might be an incompatibility...
Hello,
I have a situation where I would like to reset the MCU (nRF52832) under Zephyr. For the most part I use ```sys_reboot(SYS_REBOOT_COLD)```. However, I would need...
Hi,
I just downloaded both versions 1.7.0 and 1.7.1. Compiling asset_tracker_v2 right out of the box with west build -b nrf9160dk_nrf9160_ns --pristine I get the hex files...
I built a game controller hardware for windows . I am supposed to have a few millisec. latency on notifications.
But the latency seems to be noticeable. I have also tried...
