Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Looking for advice on reading data from the BL654 UART RX pin which is getting a text data stream from an STM32 micro.
I tried the "peripheral_uart" sample app in Segger...
When "Zigbee Dongle" is successfully connected and communicated with terminal devices, if the terminal devices that have been successfully connected to the network are all...
Hi there
We are trying to modify the MQTT_Simple example to be able to send more info than the status of pressing a button and having a button pressed notification go back...
Hi, I wanted to merge two example projects: "ble_central/ble_app_uart_c" so I have central client application, and a "peripheral/ble_usbd_ble_uart" so I have working USB CDC...
Hi everyone,
Im working and learning for private project CAN bus sniffer which when receive some data trigger some relay...
I have mcp2515_can hw-184 board on which Im...
Hey all I've had some issues with the zephyr installation and have followed the steps for setting up the toolchain. When im building a project from the command prompt it fails...
Dear Sirs,
In my current project I use nRF52 and external ADC. I have to send 14 Bytes each 500us using UART to PC.
It is only one way connection where nRF52840 is transmitter...
I'm attempting to cause the watchdog timer to timeout and activate for a verification test. I'm using Segger Ozone as my debugger. My OS platform is Windows10. I cannot seem...
I wonder what external load (if any) can be connected to the VDD pin of the nRF52805. Reading the data sheet gives the impression it is for internal loads only, but I assume...
Hi,
Today I realized something interesting for our devices: The Update from an older Software Version build with SDK 1.6.X was on it and I updated via AWS FOTA to new version...
Hi,
I am working on the v1.7.0 and I am trying to connect two peripheral with the same services to a central. The first works without any problems:
When I unplug / disconnect...
Hi
I have been experimenting with ncs recently, just trying different things out.
I'm making an application based on the following example (Which is basically code from...
I would like to add dynamically notify callbacks on a given characteristic.
Currently I can only register one callback on the creation of the characteristic:
How can...
Hello,
I notice that there is a memory region table shown when the program is compiled.
Memory region Used Size Region Size %age Used FLASH: 106392 B 960 KB 10.82% SRAM...
I have a firmware which uses FDS to store configuration, and I want to set some defaults at manufacture. The data might be hundreds of bytes. I could write the data as a binary...
